Instructions / Assembly

ManualsBrandsUltra Play ManualsKitchenToday Rainbow Lake Stainless Steel Commercial Playground In-Ground Footers Kit

Parts List

PART NUMBER

QTYDESCRIPTION

02-07-00291HDPE CLIMBER

02-07-00332

GRAB BAR

02-07-00442EXTENSION TUBE

02-07-00462

FOOTER PLATE

02-07-00394

TUBE CLAMP

33-12-00761

33-11-0003*

M10 x 25mm (1") BHCS BOLT

33-11-0200*

M10 FLATWASHER

33-11-0005*

M10 x 35mm (1 3/8") BHCS BOLT

33-11-0400*

M10 LOCK NUT

33-11-0301*

M8 LOCKWASHER

33-11-0500*

M8 LOCK NUT

33-11-0700*

CLAMP RIVET

33-11-0103*12M8 x 25mm (1") BHCS BOLT

04/30/13

HDPE CLIMBER 02-07-5018

uPLAY TODAY

800.458.5872

www.ultraplay.com

HARDWARE COMPLETE

Items listed below Hardware Complete line are included with Hardware Complete Number

Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store

Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any

Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end

protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.

Promptly cut-off flush, file smooth, and treat to prevent corrosion.

Unless Otherwise Specified, All Units of Measure are Each

Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.

Note: Loctite (supplied by others) should be used on any non-patch hardware.

INSTALLATION INSTRUCTIONS:

IMPORTANT:

DETERMINE WHICH MOUNTING OPTION YOU ARE USING; SURFACE MOUNT, ONGROUND, OR IN-GROUND.

1. Choose the appropriate Deck to receive HDPE Climber.

2. Trim out all slots in Deck with utility knife if necessary.

3. Attach Extension Tube to Footer Plate using M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut. See Detail 036.

4. Insert Extension Tube into shaft of HDPE Climber and secure with M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut. See Detail 043.

NOTE:

IF 2" SURFACING IS USED; ELIMINATE EXTENSION TUBE, AND BOLT HDPE CLIMBER DIRECTLY TO FOOTER PLATE.

5. Attach HDPE Climber to Deck using M10 x 25mm B.H.C.S. Bolt, M10 Flat Washer, and M10 Lock Nut. See Detail 031.

6. Insert shaft of Tube Clamp onto Grab Bar and secure using M8 x 25mm B.H.C.S. Bolt and M8 Lock Washer. See Detail 029.

NOTE:

THE VERTICAL POSITION OF THE GRAB BARS MUST BE A MINIMUM OF 38" ABOVE THE DECK. THE CLAMP

POSITION CAN BE ADJUSTED HIGHER TO AVOID INTERFERENCE WITH OTHER CLAMPS.

7. Attach Tube Clamp to Upright using M8 x 25mm B.H.C.S. Bolt and M8 Lock Nut. Once all clamps are installed and secured, drill

Ø1/4" hole through Clamp and Upright to install Clamp Rivet. See Detail 030. (Do not install Clamp Rivet until entire unit is

assembled.)

8. Plumb and level entire assembly before tightening all fasteners. NOTE: Apply Loctite to threads of Bolt to prevent from loosening.