Installation Guide

ManualsBrandsUltra Play ManualsFitness EquipmentFitTech Cross-Trainer Manual Elliptical

HARDWARE COMPLETE

Parts List

PART NUMBER

UP171S (SURFACE)UP171I (IN GROUND)UP171F (FOOTING)DESCRIPTION

206581111

ELLIPTICAL

206700111BASE COVER

206467010

FOOTBUCK WELD ASS'Y

206517100

206518001

206519010

135038*

020

1/2" ANCHOR ROD

801533*

040

3/4" x 2" HEX HEAD CAP SCREW

206358*

003/4" WEDGE ANCHOR

800001*

004

3/4" ANCHOR BOLT

804058*0483/4" HEX NUT

817420*

048

3/4" FLATWASHER (2" O.D.)

817354*4443/4" LOCKWASHER

Issued/Revised:

08/30/13

UP171F ELLIPTICAL (FOOTING)

FitTech

800.458.5872

www.actionfitoutdoors.com 1

ActionFit

UP171I ELLIPTICAL (IN GROUND)

UP171S ELLIPTICAL (SURFACE)

Items listed below Hardware Complete line are included with Hardware Complete Number

Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store

Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any

Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end

protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.

Promptly cut-off flush, file smooth, and treat to prevent corrosion.

Unless Otherwise Specified, All Units of Measure are Each

Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.

Note: Loctite (supplied by others) should be used on any non-patch hardware.

SPECIFICATIONS:

BASE COVER: The Base Cover shall be constructed from aluminum and powder coated.

BOLT CAP: The Bolt Cap shall be constructed from aluminum and powder coated.

FOOTREST: The Footrest shall be constructed from injection molded Nylon W6.

HANDLE GRIP: The Handle Grip shall be constructed from injection molded PVC.

INSTRUCTIONS: The Instructions shall be constructed from aluminum produced by silk-screen printing.

MAIN PIPE: The main frame shall be an all welded assembly fabricated from SPP (carbon steel pipe) and dual phase steel plate.

The frame shall be powder coated.

SADDLE: The Saddle shall be constructed from injection molded Nylon W6.

HARDWARE: All nuts, bolts, screws, and lock washers used in the assembly shall be stainless steel, yellow dichromate plated

steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary

fasteners shall be 304 alloy stainless steel. Fasteners with yellow dichromate treatment have an electro-deposited,

99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat

designed to work in conjunction with the zinc plating.

Summary of content (10 pages)

PAGE 1
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) DESCRIPTION ELLIPTICAL Parts List UP171F (FOOTING) UP171I (IN GROUND) UP171S (SURFACE) PART NUMBER 1 1 1 206581 BASE COVER 1 1 1 206700 FOOTBUCK WELD ASS'Y 0 1 0 206467 HARDWARE COMPLETE HARDWARE COMPLETE 0 0 1 206517 1 0 0 206518 HARDWARE COMPLETE 0 1 0 206519 1/2" ANCHOR ROD 0 2 0 135038* 3/4" x 2" HEX HEAD CAP SCREW 0 4 0 801533* 3/4" WEDGE ANCHOR 0 0 4 206358*
PAGE 2
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is completed. Bracing material is required during assembly. NOTE: Assembly and leveling times will be greatly reduced if a transit is used to set location and depth of ground holes.
PAGE 3
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) MAINTENANCE PROCEDURE: Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and touch-up if necessary with paint. Check for welded areas and verify integrity.
PAGE 4
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) 18 in [45.71 cm] 24 in [60.96 cm] 9 in [22.84 cm] 24 in [60.96 cm] PLAN VIEW UP171F (FOOTING) 57 5/8 in [146.35 cm] 90° 7 3/16 in [18.26 cm] 24 in [60.96 cm] 24 in [60.96 cm] ELEVATION VIEW UP171F (FOOTING) Issued/Revised: 08/30/13 800.458.5872 www.actionfitoutdoors.
PAGE 5
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) 18 in [45.70 cm] 24 in [60.96 cm] 9 in [22.84 cm] 24 in [60.96 cm] PLAN VIEW UP171I (IN GROUND) 58 1/8 in [147.70 cm] 90° IN GROUND MOUNT MUST HAVE 3" OF SURFACING 7 11/16 in [19.60 cm] 24 in [60.96 cm] 24 in [60.96 cm] ELEVATION VIEW UP171I (IN GROUND) Issued/Revised: 08/30/13 800.458.5872 www.actionfitoutdoors.
PAGE 6
ActionFit FitTech UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) 9 in [22.86 cm] 18 in [45.79 cm] PLAN VIEW UP171S (SURFACE) 57 5/8 in [146.35 cm] 90° 7 3/16 in [18.26 cm] EXISTING CONCRETE MUST BE 4" MINIMUM DEPTH ELEVATION VIEW UP171S (SURFACE) Issued/Revised: 08/30/13 800.458.5872 www.actionfitoutdoors.
PAGE 7
0 INCH 0 CM 1 3 2 1 2 5 4 3 6 7 5 4 8 9 10 11 12 6 13 14 15 UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) 3/4" HEX NUT (804058) 3/4" LOCKWASHER (817354) 3/4" FLATWASHER (2" O.D) (817420) BASE PLATE 3/4" FLATWASHER (2" O.D.) (817420) EARTH 3/4" HEX NUT (804058) CONCRETE (CURE 7 DAYS MIN.) 24" CONCRETE REQUIRED: .23 CUBIC YARDS .18 CUBIC METERS NOTE: -SLOPED FOOTING IS A REQUIREMENT OF EUROPEAN STANDARD EN1176-1 ONLY.
PAGE 8
0 INCH 0 CM 1 2 3 2 1 5 4 3 7 6 5 4 8 9 10 11 12 6 13 14 15 UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) IN-GROUND MOUNT MUST HAVE 3" OF SURFACING 3/4" x 2" HEX HEAD CAP SCREW (801533) BASE PLATE 3/4" FLATWASHER (2" O.D.) (817420) 3/4" LOCKWASHER (817354) 3/4" HEX NUT (804058) 24" [60.96 cm] EARTH 1/2" ANCHOR ROD (135038) CONCRETE CONCRETE REQUIRED: .30 CUBIC YARDS .23 CUBIC METERS 24" [60.
PAGE 9
0 INCH 0 CM 1 2 3 2 1 3 5 4 6 7 5 4 8 9 10 11 12 6 13 14 15 UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) 3/4" HEX NUT (804058) 3/4" LOCKWASHER (817354) BASE PLATE 3/4" FLATWASHER (2" O.D.) (817420) WIRE MESH WEDGE ANCHOR (206358) EXISTING CONCRETE MUST BE MINIMUM 3,000 PSI, 4" MINIMUM DEPTH, WITH WIRE MESH REINFORCEMENT. MINIMUM 7 DAYS CURE-FULL CURE AFTER 28 DAYS.
PAGE 10
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 UP171F ELLIPTICAL (FOOTING) UP171I ELLIPTICAL (IN GROUND) UP171S ELLIPTICAL (SURFACE) BASE COVER NUT BASE COVER EQUIPMENT POST BASE COVER BOLT BASE COVER BOLT NOTE: BASE COVER BOLT AND BASE COVER NUT ARE INCLUDED WITH BASE COVER. BASE COVER NUT BASE COVER BASE COVER DETAIL Issued/Revised: 08/30/13 800.458.5872 www.ultraplay.