Instructions / Assembly
Figure 1
Models which use this diagram:
SR400 and EL400
Step B. After installing the bracket (Step
A), center the window well cover in it’s fi-
nal position. Place a mark on the window
well cover over the top holes on the
bracket. This mark is where you will drill a
5/16” hole for the clevis pin.
Window Well Cover
Window Well
Outside
Inside Window Well
Clevis Pin
U-Bolt
Bracket
Flange
Nuts
Step A. Prior to drilling - Using a pencil or
marker, (inside of window well) hold and
mark the hole positions of each bracket.
Double check and make sure the top of
each bracket is level with the window well
cover before drilling.
Concrete / Brick window wells - Supplement
U-Bolts with appropriate masonry fastener to
secure bracket to window well.
Wood / Timber window wells - Supplement
U-Bolts with appropriate “lag” type screw to
secure to wood window well.
Models which use this diagram:
SR500
EL500, EL600, EL700, RT524, RT536,
RT500, RT541, RT542, RT550, RT555,
RT575, RT600, RT642, RT665, RT669,
RT675, RT700, RT795
Figure 2
Additional
Aluminum
Support
Outside
Figure 3
QUICK INSTALLATION METHOD
DOES NOT REQUIRE YOU TO CUT U-BOLTS
Additional
Aluminum
Support
Outside
Outside
Models which use this diagram:
SR500
EL500, EL600, EL700, RT524, RT536,
RT500, RT541, RT542, RT550, RT555,
RT575, RT600, RT642, RT665, RT669,
RT675, RT700, RT795
Models which use this diagram:
SR400 and EL400
Figure
5
Rear Braces Must Be Installed
Your window well cover has been supplied with a rear brace set
(rear braces and blue concrete screws). Depending upon your
installation, it may be easier to perform this step working from
inside your window well. Spaced evenly, mark the hole positions
of each rear brace which will be installed to your home, directly
under the main, aluminum support. Once you have marked
these positions on the house foundation, drill (using a 5/32”
masonry drill bit) all of the holes. Attach and tighten the rear
braces as shown in the diagram on the left.
Concrete
Screws
Window Well
Cover
Rear Brace
House
(Concrete
Foundation)
Rear Aluminum Support
Practice removing the pull pins and insure that everyone living in the home is familiar
with the removal of the window well cover and its operation.
WARNING - DO NOT INSTALL OR USE ANY TYPE OF LOCK OR DEVISE OTHER THAN
THE QUICK RELEASE PULL PINS!
Recommended Maintenance - To ensure safe operation and quick release of
your window well cover, you should remove and clean the window well cover,
about every 6 months. You should wipe down the entire window well cover,
clevis pins, Quick Release Pull Pins and the brackets. Never use solvents or
harsh chemicals when cleaning any part of the window well cover.
Pricing, specifications and availability may change at any time without notice
Dyne, Inc. - Ultra Protect Division - Minooka, IL
windowwell.com
Dyne, Inc.
®
warrants that its Ultra Protect window well covers
TM
will be warranted for life from the date of purchase. This warranty only
extends to the original consumer purchaser and is not transferrable. This warranty does not apply to damage from accident, vandal-
ism, natural acts of God, fire, misuse, alteration, improper assembly, improper installation, improper maintenance or abuse. In the
event this window well cover becomes defective, the manufacturer will, at its option, arrange for replacement or repair of the window
well cover within 45 days of receipt of written notice of such defect together with proof of purchase in the way of an original store
receipt. Dyne, Inc.
®
will repair or replace a defective window well cover free of charge (except for dealer labor and shipping). Contact
Dyne, Inc.
®
at the Internet address below or see your Ultra Protect
TM
dealer to obtain service under this warranty. Repair or replace-
ment shall be the sole remedy of the purchaser under this warranty, and in no event shall Dyne, Inc. be liable for any incidental or
consequential damages, losses or expenses. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
LIFETIME WARRANTY
dyneproducts.com
Figure 4
The Quick
Release Pull
Pins MUST
be installed
as pictured.
Flange
Nuts
Flange
Nuts
Rev. 2/04