Product Manual

ManualsBrandsUltra Safe ManualsFall ProtectionFull Body Harness with D-ring Center Back Only

WARNING!

This product is part of a personal fall

arrest system. The user must read and

follow the manufacturer’s instructions

for each component of the system. These

instructions must be provided to the user

of this product. The user must read and

understand these instructions before

using this product. Manufacturer’s

instructions must be followed for proper

use and maintenance of this product.

Alteration or misuse of this product, or

failure to follow instructions may result

in serious injury or death.

USER INSTRUCTION MANUAL

MODEL:

96305, 96307, 96305N, 96305FB,

96305F, 96305WS, PF-96305N, PF-96305,

UPF-96305, 96305NALK

DESCRIPTION: PARACHUTE BUCKLE HARNESS

MEETS OSHA & ANSI Z359.1-07

1-800-850-5914

PHOENIX, AZ USA

WWW.ULTRASAFEUSA.COM

MODEL:

_________________________

SIZE: ____________________

DATE: ___________________

Anchorage: The anchorage to which this product

is attached must be capable of sustaining a static

load in the direction applied by the personal fall

arrest system of at least 3600 lbs. with

certification of a qualified person or 5000 lbs.

without certification. When more than one

personal fall arrest system is attached to the

same structure, the strength requirements stated

above must be multiplied by the number of

personal arrest systems attached to the

structure.

Plan your personal fall protection system.

Before installing and using this equipment,

consider all factors affecting your safety

during use of this equipment.

Warning: Manufacturer's instructions supplied

with this product at time of shipment must be

followed. Failure to do so could result in serious

injury or death. Contact manufacturer if

instructions are needed.

• Warnings and instructions must be read and

understood before using equipment.

• Equipment must be used by trained

personnel only.

• Users must understand all OSHA regulations,

ANSI standards, and other relevant

regulations and standards pertaining to fall

protection equipment.

This product is part of a

personal fall arrest

system; a fall arrest

system is required if

there is any risk that a

worker may fall from an

elevated position. It is a

requirement that the fall

arrest system be used

any time a working

height of six feet or more

is reached. Working

height is defined as the

distance from the walking/working surface to a

grade or lower level.

The following is recommended as part of fall

arrest system.

A. Full Body Harness Material: Nylon

1. Back D-ring is for fall arrest

2. Shoulder D-rings (if present) are

for retrieval use only.

3. Side D-rings (if present) are

for positioning only.

4. Warning tags.

Note: See additional instructions on buckle adjustment

for proper fit. Maximum free-fall distance six feet or

maximum fall arrest force of 1800 lbs. Avoid lower level

contact.

B. Shock Absorbing Lanyard Material: Nylon

Warning tags located

in front and back of

shock absorber or

located towards hook,

D-ring or eye end.

• Energy absorber resting force 900 lbs.

Plus 42 inch maximum extension.

• Rig lanyard to allow a maximum free fall distance

of not more than six feet.

• Connectors and anchorage points must be

compatible and able to support 5,000 lbs.

• Do not allow lanyard to contact sharp or abrasive

surfaces, sparks or temperature above 180 degrees.

• Snap hooks with gate openings larger than

one inch (1") must not be connected to D`-rings

on harnesses and belts.

• Remove from service if any damage is detected.

C. Anchorage connector material: Nylon

Warning tags are

located towards hook,

D-ring or eye end.

•

Use energy absorbers

or retractable lanyards

when hazard of free fall can occur.

• Connectors and anchorage points must be compatible

and able to support 5,000 lbs. Always work directly

under anchorage to avoid a swing fall injury.

• Anchorage and tie off points must be at a height

that will not allow a lower level to be struck should

a fall occur. Do not allow product to contact sharp

or abrasive surfaces, sparks or temperatures

above 180 degrees.

• Snap hooks with gate openings larger than

one inch (1”) must not be connected.

•

Remove from service if any damage is detected.

313H1

Summary of content (4 pages)

PAGE 1
USER INSTRUCTION MANUAL MODEL: 96305, 96307, 96305N, 96305FB, 96305F, 96305WS, PF-96305N, PF-96305, UPF-96305, 96305NALK 1-800-850-5914 DESCRIPTION: PARACHUTE BUCKLE HARNESS PHOENIX, AZ USA WWW.ULTRASAFEUSA.COM MEETS OSHA & ANSI Z359.
PAGE 2
Parachute buckle harnesses come in different styles, pads on back, no tool belt, etc., but proper adjustment and fit is critical. Refer to these instructions for key adjustment points. 1. Hold harness by back D-ring. Shake harness to allow all straps to fall into place. 2. Slip straps over shoulders so D-ring is located at middle of back. 5. Pull leg straps around to the outside of leg and fasten. 4. Pull chest strap around shoulder strap and fasten at mid chest. Tighten to keep shoulder straps taut.
PAGE 3
Harness System Inspection Procedures General 1. Check for wear and deterioration. Before each use, carefully inspect your harness for signs of wear, deterioration, or evidence of impact loading. Visually inspect for loose threads, pulled rivets, burns, cuts, distortions, abrasions, or any other evidence of chemical or physical deterioration that may have weakened the material or assembly. 2. Inspect hardware for malfunctions and cracks. Check all snap hooks, buckles and D-Rings. 3.
PAGE 4
Inspection Date Inspection Items Noted Corrective Action Maintenance Performed Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: EXAMPLE OF TAGS WARNING! The user must read and understand these instructions or have them explained to them, before using this equipment. Failure to follow instructions may result in serious injury or death.