INSTALLATION GUIDE 2500 2500M Advanced Remote Vehicle Starter & Alarm WWW.ULTRASTARTERS.COM TECH SUPPORT Western Canada 1 800 279-0636 United States: 1 866 698-5872 Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail Tech Support: support@ultrastarters.com Check Our Web Site: www.ultrastarters.
Installation Guide TABLE OF CONTENTS 2500 Wiring Diagram Pre-Installation Components Recommended Pre-Installation Procedures Recommended Install procedures Wire Connectors 6 Pin Connector 14 Pin Connector 3 Pin Red Connector 4 Pin Blue Connector Jumper Selections Installation Basic Installation - Quick start Plugging In The Module Auto Tach Learn Shock Sensor Programming Programming Program Overview & System Reset Program Menu 1 (User Settings) Program Menu 2 (Alarm Settings) Program Menu 3 (Starter Settin
Installation Guide WIRING DIAGRAM Starter Yellow (+) 30amp Output Heater Green (+) 30amp Input Main Power Red (+) 30amp Input Main Power Red (+) 30amp Output Selectable P.
Installation Guide INSTALLATION TIPS Components - Control module - Remote transmitter(s) - Antenna with built in Program Button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 4 pin square harness. - 4 pin keyless entry harness - 4 pin Aux. sensor harness - Multi-tone Siren - Hood pin safety switch - Installation guide - Owners manual Recommended Pre-Installation Procedures BEFORE STARTING INSTALLATION: - Discuss the optional features with the customer.
Installation Guide WIRING CONNECTORS 6 Pin Power Connector Yellow Green Red Red Blue White Starter Heater 12 power 12 power Ignition 1 Selectable 30amp output 30amp output 30amp input 30amp input 30amp output 30amp output 12volts during crank only. 12volts in accessory. Off during start. Constant 12volt power at ignition harness. Constant 12volt power at ignition harness. 12volts in ignition and start positions. Jumper Selectable. See Page 5.
Installation Guide QUICK START INSTALL Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Green Red Red Blue White Starter Output Heater Output 12 power Input 12 power Input Ignition 1 Output Selectable Output Connect To The Vehicles Starter Wire. Connect To The Vehicles Accessory Wire. Connect to Constant 12 Volt Power Source- High Current. Connect to Constant 12 Volt Power Source- High Current. Connect To the Vehicles Primary Ignition. Select Jumper Position (If Necessary).
Installation Guide PROGRAMMING Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications.
Installation Guide PROGRAMMING PROGRAM MODE - USER SETTINGS Enter User Program Mode - See Page 7 for details on entering program mode Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 2 Ignition Lock Only *3 Ignition Auto Lock Disabled 1 Light Flash 2 Light Flashes 3 Light Flashes Doors Lock / Unlock when the key is turned On/ Off Doors Lock when ignition key is turned ON only Doors do not Lock or Unlock with Ignition key Press the Program Switch 1 time to select setting 1 (This will be co
Installation Guide PROGRAMMING PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Setting 1 - Car Finder / 5th Channel 1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled *2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled Note: To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
Installation Guide PROGRAM MODE - STARTER SETTINGS Enter Starter Program Mode - See Page 7 for details on entering program mode Setting 1- Special Door Lock/ Unlock Operations 1 Chrysler / VW Re-Arm 1 Flash Unlock pulse before start and a lock pulse after start 2 GM Auto Re-Lock 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program
Installation Guide Setting 8- Safety Start Mode 1 2* Safety ON Safety OFF 1 Flash 2 Flashes Must press the start button twice to remote start vehicle Press the start button once to remote start vehicle. Press the Program Switch 8 times to select setting 8 (This will be confirmed by 8 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps. Release the Program Switch.
Installation Guide OPERATIONS Reservation Mode - Manual Trans. Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a “M” Series Remote Starter on a manual transmission vehicle.
Installation Guide OTHER FEATURES System Service Mode ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady. Door locks and trunk release are still operational. DEACTIVATING SERVICE MODE 1.
Installation Guide OPERATIONS Lock Doors & Arm The Alar m 1. 2. 3. 4. Press & release the LOCK button on the remote transmitter. The park lights will flash and the siren will chirp once. The doors will lock. The LED will start flashing within five seconds. Unlock Doors & Disarm The Alar m 1. 2. 3. 4. Press & release the UNLOCK button on the remote transmitter. The park lights will flash and the siren will chirp twice. The doors will unlock. The LED will stop flashing.
Installation Guide OPERATIONS Remote Start 1. Press & release the button. 2. The Park lights will flash and the siren will chirp once. 3. When the vehicle has started, the system will flash the park lights four times and then remain “On” while the vehicle is running. 4. The vehicle will continue to run for the programmed runtime. (normally 15 minutes). EXTEND RUNTIME 1. Press & release the button while the vehicle is running. 2.
Installation Guide RELAY DIAGRAMS Negative Door Locks Vehicle Lock/Unlock Switch Lock To Control Relay or Actuators Un lock Green Blue Positive Type Door Locks Vehicle Lock/Unlock Switch Un Lock lock Fused +12V 87 Green 87 87a 86 Blue 87a 86 85 30 85 30 To Control Relay or Actuator 5 Wire / Reverse Polarity Type Door Locks Fused +12V 87 Green 87 87a 86 Blue Vehicle Lock/Unlock Switch 87a 86 85 85 30 Lock 30 x Cut Un lock To Actuator Cut x Vacuum Type Door Locks DIAGNOSTICS