INSTALL GUIDE Covers All 32xx and 33xx Series Remote Starters REMOTE STARTERS CAR ALARMS ü WWW.ULTRASTARTERS.COM Technical Support 866-698-5872 ext 0 Support@ultrastarters.com -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 2 Table of Contents Table of Contents Pre-Installation Components Feature List Pre-Installation Installation Procedures Wiring Diagrams Wire Description 6 Pin Connector Auxiliary Connectors Optional Connectors Jumper Positions Quick Start Installation Basic Installation Plug-in The Module Manual Transmission Vehicles Additional Connections Clutch Bypass Important Tach Notes Auto Tach Learn Quick Tach Learn Program Overview and Quick View Programming En
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 3 Components - Control module - Antenna with built in Program Button - 14 pin harness* - 3 pin keyless entry harness - Hood pin safety switch - 2way LCD remote transmitter - 6 pin main harness - 11 pin harness** - 4 pin harness** - 2 pin Harness (3350 and LT Models) - Installation and Owner Manuals * 32xx series ** 33xx series Feature List - Auto Tach learning with Quick Learn option - Turbo Timer Mode - Starter Kill/ Anti-Grind Protection - Engine I
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 4 Recommended Installation Procedures Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It is critical to insure that all high current connections are properly soldered and insulated with quality electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in damage to the vehicle and remote starter module.
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 5 Wiring Diagram - 11 pin + 4 pin Connectors 30amp Output Starter Output YELLOW 30amp Output Heater/Acc Output GREEN 30amp Input Power Input 30amp Input 30amp Output Power Input Selectable Output RED WHITE 30amp Output Ignition Output BLUE RED (-)250ma Output Factory Re-arm Output (-)250ma Output Trunk Release Output RED/WHITE (-)250ma Output Factory Disarm Output BROWN (-)250ma Output Starter kill & Anti-Grind Output YELLOW O
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 6 Wiring Diagram 14 pin connector 30amp Output Starter Output 30amp Output Heater/Acc Output 30amp Input 30amp Input 30amp Output 30amp Output YELLOW Power Input GREEN RED 2 Power Input RED 4 Selectable Output WHITE Ignition Output BLUE (-)250ma Output Factory Re-arm Output (-)250ma Output Trunk Release Output RED/WHITE (-)250ma Output Factory Disarm Output BROWN (-)250ma Output Starter kill & Anti-Grind Output ORANGE (-)250m
2WAY REMOTE STARTER/ ALARM INSTALLATION MANUAL Page 7 Wiring Diagram auxiliary connectors * The centre pin of the keyless entry harness is not to be used for anything besides plug-in devices such as the VP-1, DL-3, DL-7 and Data Bus Modules. Overloading this output will damage the remote starter.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 8 6 Pin Power Connector 6-pin 1-Yellow 2-Green 3-Red 4-Red 5-Blue 6-White Description Test For Wire 30amp Starter Output - This wire will test 0volts in off, accessory and in the ignition position.12volts during start only. 30amp Heat/Acc Output - This wire will test 0volts in the off position 1214volts in the accessory and run positions and 0 volts during start 30amp Power Input - 12volts at ignition harness or from battery.
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 9 Auxiliary Connectors - continued from previous page 11-Black 12-Blue Ground - System Chassis Ground Input. Glow Plug - Diesel Glow plug input, detects both 12volt and negative glow plug signals. Programmable input. See Menu 3. 13-Blue/White Tach - A/C Tach Signal Input. Used to detect when the vehicle has started. This wire is connected to the vehicles coil, fuel injector or crank sensor wire. 14-Pink Brake input - Positive Brake Input.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 10 Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Green Red Red Blue White 30amp Starter Output - 12volts during start position only. 30amp Heater Output - 12volts in the accessory position off during start and 12volts during run. 30amp Power Input - Constant 12volt power at ignition harness or from battery. 30amp Power Input - Constant 12volt power at ignition harness or from battery.
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 11 Manual Transmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation. Park Brake Input- This wire is located at the park brake switch. The wire will switch to (-) when the park brake is applied.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 12 Auto Tach Learn 1) Turn the ignition key to the “ON” position. (The park lights will turn on*). 2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach signal is detected**, then after 30-35 seconds the park lights will flash and the horn (Optional) will honk twice to confirm Tach Learn. * If the park lights do not turn on check for proper connection on the BLUE ignition wire at the 6-pin connector.
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 13 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process. Do not tach learn vehicle while the engine is in high idle. To ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM. Vehicles such as Toyota and Honda may idle much higher when the engine is warm compared to starting the vehicle when the engine is cold.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 14 Entering Program Mode 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park lights will flash and the horn (optional) will honk to confirm entering program mode. 3) Select desired Program Menu (See below).
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 15 Quick View Programming * See the following pages for more detailed programming instructions. Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Horn Honk Type 1 Type 2 All Honks 3 Lock&Unlock Options Double Unlock 3 second .
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 16 1 2 34 Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #1 Ignition 3x On/Off On/Off On Press and Release the Program Press button Button 1 to enter Program Menu 1 Press and Release the Program Switch 1x =Setting 1 2x =Setting 2 3x =Setting 3.... Press and Hold the Program Switch 1x = Option 1 2x = Option 2 3x = Option 3....
2WAY REMOTE VEHICLE STARTER Menu 2- Additional Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #2 INSTALLATION MANUAL 1 2 34 Ignition 3x On/Off On/Off On Press and Release the Program Button Press and Release the Press button Program Switch 2 to enter 1x =Setting 1 Program 2x =Setting 2 Menu 2 3x =Setting 3.... Press and Hold the Program Switch 1x = Option 1 2x = Option 2 3x = Option 3....
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 18 Menu 3- Starter Settings 1 2 34 Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button#3 Ignition 3x On/Off On/Off On Press and Release the Program Button Press and Release the Press button Program Switch 3 to enter 1x =Setting 1 Program 2x =Setting 2 Menu 3 3x =Setting 3.... Press and Hold the Program Switch 1x = Option 1 2x = Option 2 3x = Option 3.... Setting 1 Special Door Lock/Unlock Operations (Factory Alarm Rearm).
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Menu 3- Starter Settings - Continued From Previous Page Page 19 Setting 4 Run Time 1) 4 Minutes 1 Flash/Honk Runs for approximately 4 minutes when activated. 2) 45 Minutes 2 Flashes/Honks Runs for approximately 45 minutes when activated. *3) 15 Minutes 3 Flashes/Honks Runs for approximately 15 minutes when activated. Press & Release the Program Button 4 Times (Setting 4) Confirmed with 4 LED flashes.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 20 Menu 4- Tach Settings 1 2 34 Ignition 3x On/Off On/Off On Setting 1 Auto Tach Learn. Press and Release the Program Button Press and Release the Press button Program Switch 4 to enter 1x =Setting 1 Program 2x =Setting 2 Menu 4 3x =Setting 3.... Press and Hold the Program Switch 1x = Option 1 2x = Option 2 3x = Option 3.... 1) 2) 3) 4) Perform a System Reset. See page 15. Turn the ignition key on. (Park lights will turn on).
2WAY REMOTE VEHICLE STARTER INSTALLATION MANUAL Page 21 Transmitter Programming Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Button - The park lights will turn ON and the siren will chirp once.* Continue to hold the Program Button, the park lights will turn off and the siren will chirp 5 times quickly. Step 3 - While holding the Program Button, press the LOCK button on each of the remote’s to be programmed.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 22 Negative Type Door Locks 250ma Vehicle Lock/Unlock Switch Lock To Control Relay or Actuators Un lock Green Blue Negative Door Locks (More Than 250ma) Fused +12V Vehicle Lock/Unlock Switch Ground Green 87 87 87a 86 87a 85 Blue Un Lock lock 86 85 30 30 To Control Relay or Actuator Positive Type Door Locks Un Lock lock Fused +12V Green 87 87 87a 86 Blue Vehicle Lock/Unlock Switch 87a 85 30 86 85 30 To Control Relay or Actu
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 23 5 Wire / Reverse Polarity Type Door Locks Fused +12V 87 Green 87 87a 86 Blue 85 30 Lock Vehicle Lock/Unlock Switch 87a 86 85 30 x Cut Un lock To Actuator x Cut Aftermarket Doorlock Actuators Ground 87 87a 86 85 30 Vacuum Type Door Locks DIAGNOSTICS Ground Fused +12V Blue Lock Un lock 87 87 87a 87a 86 85 86 30 85 30 x Cut To Vacuum Pump 13 Green Note: When installing relays always use a fused power source.
INSTALLATION MANUAL 2WAY REMOTE VEHICLE STARTER Page 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the park lights flash 3 times slowly.