- Applicated Security Technologies Automobile Alarm User Manual

Menu 3- Starter Settings - Continued From Previous Page
Setting 2 With 14pin Connector- Gas/Diesel Mode (Auxiliary Connector Pin 12)
1) (-) Input 1 Flash/chirp (-) Glow Plug input. Waits maximum 30 seconds then starts.
2) Time Delay 2 Flashes/chirps Waits for approximately 15 seconds then remote starts.
*3) Gas/ (+) Input 3 Flashes/chirps Waits 2 seconds to start if no diesel input is detected.
Press & Release the Program Button 2 Times (Setting 2) Confirmed with 2 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Note: Setting 2 will vary depending on the board layout 11 or 14 pin connectors.
Setting 3 Rearm Output (Auxiliary Connector Pin 1)
1) Type 1 1 Flash/chirp Pulse after start and with lock. (Provides Lock Pulse)
2) Type 2 2 Flashes/chirps Pulse after start only. (Provides Lock Pulse)
*3) Factory Re-arm 3 Flashes/chirps Pulse with lock and after starter shutdown.
Press & Release the Program Button 3 Times (Setting 3) Confirmed with 3 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 4 Run Time
1) 4 Minutes 1 Flash/chirp Runs for approximately 4 minutes when activated.
2) 45 Minutes 2 Flashes/chirps Runs for approximately 45 minutes when activated.
*3) 15 Minutes 3 Flashes/chirps Runs for approximately 15 minutes when activated.
Press & Release the Program Button 4 Times (Setting 4) Confirmed with 4 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 5 Maximum Crank Time
1) 10 Seconds 1 Flash/chirp 10 sec max time that the starter will stay engaged.
2) 3 Seconds 2 Flashes/chirps 3 sec max time that the starter will stay engaged.
*3) 5 Seconds 3 Flashes/chirps 5 sec max time that the starter will stay engaged.
Press & Release the Program Button 5 Times (Setting 5) Confirmed with 5 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 6 Anti-Grind/Starter Kill (Auxiliary Connector Pin 4)
1) Active 1 Flash/chirp (-) when locked and during remote start (Anti-Grind).
2) Passive 2 Flashes/chirps (-) when locked /30 seconds after ignition is Off or unlock is pressed
*3) Anti-grind 3 Flashes/chirps Output during remote start only. (Anti-grind/ Bypass module)
Press & Release the Program Button 6 Times (Setting 6) Confirmed with 6 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
Setting 7 Safety Start
1) Safety On 1 Flash/chirp Press the start button twice within 3seconds to remote start vehicle.
*2) Safety Off 2 Flashes/chirps Press the start button once to remote start vehicle.
Press & Release the Program Button 7 Times (Setting 7) Confirmed with 4 LED flashes.
Press & Hold the Program Button until the appropriate # of park lights/siren chirps, then release.
Press & Release the Program Button to proceed to the next step.
*(Default Settings)
2WAY REMOTE STARTER/ALARM INSTALLATION MANUAL
Page 19