INSTALL GUIDE Covers All 45xx Series Advanced 2-Way Remote Starter/Alarms www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service Mode before any service work is started on the CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH! vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 2 Table of Contents Table of Contents Component/Feature List Recommend Installation Procedures Wiring Diagrams Wire Description 6 Pin Connector Auxiliary Connectors Optional Connectors Jumper Positions Quick Start Installation Basic Installation Plug-in The Module Manual Transmission Vehicles Additional Connections Clutch Bypass Important Tach Notes Auto Tach Learn Quick Tach Learn Program Overview and Quick View Programming Entering Program Mode Quick View Prog
REMOTE VEHICLE STARTER INSTALL MANUAL PAGE 3 Components - Control module - Antenna with built in Program Button and LEDs - 14 pin auxiliary harness - 4 pin keyless entry harness - 4 pin auxiliary sensor harness - Install and Owner Guides - 4 button 2-way remote transmitter - 3 button 1-way remote transmitter - 6 pin Main harness - 4 pin auxiliary harness - 2 pin LT/ Instant Start harness - Multi-tone Siren - Hood pin switch Feature List - Auto Tach (Tachless, TL series only) learning with Quick Learn -
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 4 Recommended Installation Procedures Remote car starters and alarms should be professionally installed. Review the installation and owner manuals and acquire a vehicle wiring diagram for the vehicle to be worked on. Take a few moments to walk around the vehicle looking for any damages and make note if any are found. Also check other functions such as the lighting system, warning or check engine lights.
REMOTE VEHICLE STARTER INSTALL MANUAL PAGE 5 Recommended Installation Procedures Mounting The Control Module - Never mount the module in the engine compartment. Select a location under the dash to install the main module. Be certain that the module is securely attached and does not obstruct any serviceable areas. Do not force or jam the module into tight places instead of mounting. The module must be free from all moving parts such as brake, clutch and gas pedal linkages.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 6 Wiring Diagram Starter Output (+) YELLOW Heater/Accessory Output (+) GREEN 12volt Input (+)30amp RED 12volt Input (+)30amp RED Selectable Output (+)* WHITE* Ignition Output (+) BLUE Re-arm Output (-)250ma YELLOW Starter Kill/ Anti-Grind Output (-)250ma ORANGE Dis-arm Output (-)250ma BROWN Trunk Release Output (-)250ma RED/WHITE Ground While Running Output (-) WHITE/VIOLET Negative Door Pin Input (-)** GREEN** Hood Pin Switch Input (-)
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 7 Wiring Diagram continued...
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 8 Wiring Descriptions MAIN CONNECTOR (6pin) Pin Function Description 1-YELLOW Starter Output - This wire will test 0V in OFF, ACCESSORY and in the 2-GREEN 3-RED 4-RED 5-BLUE 6-WHITE ON key positions. 12v during START ONLY. Heater/Acc Output - This wire will test 0V in the OFF and START key positions. 12-14V in the ACCESSORY key position. 12volt Input(30amp) - Supplies 12votls for the IGNITION, PARK LIGHT and SELECTABLE outputs.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 9 Wiring Descriptions Pin 13-WHITE Function Description Park Light(+) - 10amp positive output to activate park lights. Programmable output (menu 2) 14-BLACK/ Parking Brake(-) - Input to detect (-) when parking brake switch is applied. WHITE AUXILIARY CONNECTOR (4pin white)* Pin Function 1-WHITE/GREEN 2-BLACK 3-WHITE/BLUE 4-RED Description LED(-) - External LED Output. Dome Light(-) - 250ma dome light supervision output.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 10 Step 1 - Connect All Of the Following Wires Main Connector (6pin) YELLOW GREEN RED RED BLUE WHITE* Starter Output - 12volts during start position only. Heater/Acc Output - 12volts in the accessory position off during start and 14volts during run. 12volt 30amp Input - 12volts from ignition harness or battery. 12volt 30amp Input - 12volts from ignition harness or battery. Ignition Output - 12volts in the ignition, start and run positions.
REMOTE VEHICLE STARTER INSTALL MANUAL PAGE 11 Manual Transmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation. Park Brake Input- This wire is located at the park brake switch. The wire will switch to (-) when the park brake is applied.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 12 Auto Tach Learn IMPORTANT! The system must be Tach Learned before remote starting. The Auto Tach Learn is the same for the TL (tachless) series. 1) Turn the ignition key to the “ON” position. The park lights* will turn “ON” 2) Start the vehicle with the key. The LEDs on the antenna will turn on if a proper tach signal is detected**, after 30-35 seconds the park lights will flash and the horn (Optional) will honk twice to confirm Tach Learn.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 13 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process. Do not tach learn vehicle while the engine is in high idle. To ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM. Vehicles such as Toyota and Honda may idle much higher when the engine is warm compared to starting the vehicle when the engine is cold.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 14 Entering Program Mode Ignition 3x On/Off On/Off On Press and Release the Program Button For Menu 1, For Menu 2, For Menu 3, For Menu 4, press the press the press the press the button button button button 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. NOTE: Leave the key in the ON position 2) Press and release the Program Button.
REMOTE VEHICLE STARTER INSTALL MANUAL PAGE 15 Quick View Programming Menu 1 - Press 1 Flash 2 Flashes 1 Ignition Lock Enabled Lock Only 2 Siren Output Type 1 Type 2 3 Lock&Unlock Options Double Unlock 3 second 4 Unlock/Disarm 125ms 750ms 5. Passive Locks Disable Enable 6. Shock Sensor Disable Enable 7.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 16 Menu 1- User Settings Ignition 3x On/Off On/Off On Press and Release the Program Button Press and Release the button for Menu 1 Press and Hold Press and Release the Program Button the Program Button to Change Option # of Times for Setting Chosen Setting 1 Ignition Auto Lock 1) Enable 2) Ignition Lock Only *3) Disable 1 Flash/Chirp 2 Flashes/Chirps 3 Flashes/Chirps Doors Lock/Unlock with Ignition key. Doors Lock when ignition is turned “ON” only.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 17 Menu 1- User Settings...continued Setting 6 Sensor Enable/Disable 1) Sensor Disabled *2) Sensor Enabled 1 Flash/Chirp 2 Flashes/Chirps Impact Sensor Disabled Impact Sensor Enabled Press & Release the Program Button 6 Times (Setting 6) Confirmed with 6 LED flashes. Press & Hold the Program Button until the appropriate # of park lights/ siren chirps, then release. Press & Release the Program Button to proceed to the next step.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 18 Menu 2- Additional Settings - continued Setting 3 Siren Chirp Timing 1) 5 ms Pulse Output 2) 15 ms Pulse Output *3) 10 ms Pulse Output 1 Flash/Chirp 2 Flashes/Chirps 3 Flashes/Chirps Short(Quiet) siren Output Long(Loud) siren Output Normal(Medium) siren Output Press & Release the Program Button 3 Times (Setting 3) confirmed 3 LED flashes. Press & Hold the Program Button until the appropriate # of park light/siren chirps, then release.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 19 Menu 3- Starter Settings - continued Setting 2 Gas/Diesel Mode 1) (+) Input .2) Time Delay *3) Gas/ (-) Input 1 Flash/Honk 2 Flashes/Honks 3 Flashes/Honks (+) Glow Plug input. Waits maximum 30 seconds Waits for approximately 15 seconds. Waits 2 seconds if no diesel input is detected. Press & Release the Program Button 2 Times (Setting 2) Confirmed with 2 LED flashes.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 20 Menu 4- Tach Settings - continued Ignition 3x On/Off On/Off On Press and Release the Program Button Press and Press and Release Release the the Program Button # of Times for button for Setting Chosen Menu 4 Press and Hold the Program Button to Change Option Setting 1 Low Idle Learn- Same function as doing the Quick Tach Learn.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 21 Remote Transmitter Learn STEP 1 - Within 3 seconds turn the ignition key to the “ON” position three times leaving “ON” the third time. STEP 2 - Press and hold the Program Button. The park lights will turn “ON” and the horn (optional) will honk once. Continue to hold the Program Button, the park lights will turn “OFF” and the horn (optional) will honk 5 times quickly.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 22 Door Lock Relay Wiring Diagrams Negative Type Door Locks 250ma Vehicle Lock/Unlock Switch Lock To Control Relay or Actuators Un lock Green Blue Negative Door Locks (More Than 250ma) Fused +12V Vehicle Lock/Unlock Switch Ground 87 Green 87 87a 86 87a 86 85 Blue Un Lock lock 30 85 30 To Control Relay or Actuator Positive Type Door Locks Vehicle Un Lock Lock/Unlock lock Switch Fused +12V Green 87 87 87a 86 Blue 87a 85 30 86 85 30 To Co
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 23 Door Lock Relay Wiring Diagrams 5 Wire / Reverse Polarity Type Door Locks Fused +12V 87 Green 87 87a 87a 86 Vehicle Lock/Unlock Switch 86 85 Blue 30 Lock 85 30 x Cut Un lock To Actuator x Cut Aftermarket Doorlock Actuators Ground 87 87a 86 85 30 Vacuum Type Door Locks DIAGNOSTICS Ground Fused +12V Blue Lock Un lock 87 87 87a 87a 86 85 86 30 85 30 x Cut To Vacuum Pump 13 Green NOTE: When installing relays always use a fused p
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the button is pressed the park lights flash 3 times slowly.
