Specifications

Elite Series Technical Manual PDL Part No.4201-180 Rev J
4201-003 Rev C Page 7 of 8
FIGURES
Figure 2.1: Elite Series 400V Nominal and Re-rated Specifications 11
Figure 2.2: Elite Series 500V Nominal and Re-rated Specifications 12
Figure 3.1: Microdrive Elite Series Dimensions 13
Figure 3.2: Ultradrive Elite Frame 4 Dimensions 14
Figure 3.3: Ultradrive Elite Frames 5 to 7 Dimensions 15
Figure 3.4: Elite Series Electrical Overview 16
Figure 3.5a: Power Electronics - Microdrive Elite Frames 1 & 2 17
Figure 3.5b: Power Electronics - Microdrive Elite Frame 3 17
Figure 3.5c: Power Electronics - Ultradrive Elite Frame 4 17
Figure 3.5d: Power Electronics - Ultradrive Elite Frames 5 to 7 17
Figure 3.6: The Display Unit and Keys 18
Figure 3.7a: Control Terminals T1-T21 19
Figure 3.7b: Control Terminals T22-T42 20
Figure 3.8: Structure of the Elite Series Input/Output Processing System 22
Figure 3.9: Structure of the Elite Series Motor Control System 23
Figure 3.10: Process Control 24
Figure 4.1: Elite Series Thermal Overload Characteristics 25
Figure 4.2: Typical Motor Thermal Derating 25
Figure 4.3: Dynamic Brake Resistor Ratings (Typical) 27
Figure 5.1: Elite Series Power Terminal tightening Torque 29
Figure 5.2: Elite Series Power Connection 29
Figure 5.3: Shaft Encoder Connection Details 30
Figure 5.4: Microdrive Elite Series Cable Configuration 30
Figure 5.5: Ultradrive Elite Frame 4 Cable Configuration 31
Figure 5.6: Ultradrive Elite Frame 5 Cable Configuration 31
Figure 5.7: Ultradrive Elite Frame 6 Cable Configuration 32
Figure 5.8: Ultradrive Elite Frame 7 Cable Configuration 32
Figure 7.1: The Display Unit 39
Figure 7.2: Screen Unfolding and Folding 39
Figure 7.3: Setting Commission Mode after a Password has been set 40
Figure 7.4: Setting a Password for the First Time 40
Figure 7.5: Entering and Exiting Menu Set-up Mode 41
Figure 7.6: Typical Screen Display in Menu Set-up Mode 41
Figure 9.1a: Screen List A-H 43
Figure 9.1b: Screen List I-N 44
Figure 9.1c: Screen List O-P 45
Figure 9.1d: Screen List R-Z 46
Figure 9.2: Comparator Source Selection 49
Figure 9.3: Local Start/Stop-Reset Control 53
Figure 9.4: Speed Reference Source Selection 54
Figure 9.5: Torque Reference Source Selection 54
Figure 9.6: Analogue Input Format Selection 55
Figure 9.7: Analogue Input Scaling and Torque/Speed Limits 55
Figure 9.8: Analogue Input Reference Zero Band 56
Figure 9.9: Input Mode Selection 57
Figure 9.10: Active High/Active Low Selection 58
Figure 9.11: Multi-function Input Functions (Selectable Functions) 59
Figure 9.12: Fibre Optic Control Mode Selection 59
Figure 9.13: Skip Speeds 61
Figure 9.14: Special Functions using Multi-Reference Setpoints 62
Figure 9.15: Multi-Reference 2 Wire Functions 62
Figure 9.16: Function of Multi - Reference 3 Wire 63
Figure 9.17: Analogue & Fibre Outputs Source Selection 65
Figure 9.18: Analogue Output Format Selection 66
Figure 9.19: Analogue Output Scaling 66
Figure 9.20: Relay Table Selection 67
Figure 9.21: Process Control Setpoint Source 68
Figure 9.22: Process Control Feedback Source 69
Figure 9.23: Dual Acceleration/Deceleration Rates 70
Figure 9.24: Stopping Modes 73
Figure 9.25: Start and Off Delay Times 73
Figure 9.26: Initialisation Levels 80