Datasheet
Table Of Contents
- 1. General Description
- 2. Electrical Characteristics
- 3. SX1272/73 Features
- 4. SX1272/73 Digital Electronics
- 4.1. The LoRaTM Modem
- 4.2. FSK/OOK Modem
- 4.2.1. Bit Rate Setting
- 4.2.2. FSK/OOK Transmission
- 4.2.3. FSK/OOK Reception
- 4.2.4. Operating Modes in FSK/OOK Mode
- 4.2.5. General Overview
- 4.2.6. Startup Times
- 4.2.7. Receiver Startup Options
- 4.2.8. Receiver Restart Methods
- 4.2.9. Top Level Sequencer
- 4.2.10. Data Processing in FSK/OOK Mode
- 4.2.11. FIFO
- 4.2.12. Digital IO Pins Mapping
- 4.2.13. Continuous Mode
- 4.2.14. Packet Mode
- 4.2.15. io-homecontrol® Compatibility Mode
- 4.3. SPI Interface
- 5. SX1272/73 Analog & RF Frontend Electronics
- 6. Description of the Registers
- 7. Application Information
- 8. Packaging Information
- 9. Revision History
www.semtech.comPage 57
SX1272/73
WIRELESS, SENSING & TIMING DATASHEET
Rev. 2 - July 2014
©2014 Semtech Corporation
4.2.9.2. Sequencer Transitions
The transitions between sequencer states are listed in the forthcoming table.
Table 25 Sequencer Transition Options
RxTimeout Defines the action to be taken on a RxTimeout interrupt.
RxTimeout interrupt can be a TimeoutRxRssi, TimeoutRxPreamble or TimeoutSignalSync
interrupt.
Variable Transition
IdleMode
Selects the chip mode during Idle state:
0: Standby mode
1: Sleep mode
FromStart
Controls the Sequencer transition when the SequencerStart bit is set to 1 in Sleep or Standby mode:
00: to LowPowerSelection
01: to Receive state
10: to Transmit state
11: to Transmit state on a FifoThreshold interrupt
LowPowerSelection
Selects Sequencer LowPower state after a to LowPowerSelection transition
0: SequencerOff state with chip on Initial mode
1: Idle state with chip on Standby or Sleep mode depending on IdleMode
Note: Initial mode is the chip LowPower mode at Sequencer start.
FromIdle
Controls the Sequencer transition from the Idle state on a T1 interrupt:
0: to Transmit state
1: to Receive state
FromTransmit
Controls the Sequencer transition from the Transmit state:
0: to LowPowerSelection on a PacketSent interrupt
1: to Receive state on a PacketSent interrupt
FromReceive
Controls the Sequencer transition from the Receive state:
000 and 111: unused
001: to PacketReceived state on a PayloadReady interrupt
010: to LowPowerSelection on a PayloadReady interrupt
011: to PacketReceived state on a CrcOk interrupt. If CRC is wrong (corrupted packet, with CRC on but
CrcAutoClearOn is off), the PayloadReady interrupt will drive the sequencer to RxTimeout state.
100: to
SequencerOff state on a Rssi interrupt
101: to SequencerOff state on a SyncAddress interrupt
110: to SequencerOff state on a PreambleDetect interrupt
Irrespective of this setting, transition to LowPowerSelection on a T2 interrupt
FromRxTimeout
Controls the state-machine transition from the Receive state on a RxTimeout interrupt (and on
PayloadReady if FromReceive = 011):
00: to Receive state via ReceiveRestart
01: to Transmit state
10: to LowPowerSelection
11: to SequencerOff state
Note: RxTimeout interrupt is a TimeoutRxRssi, TimeoutRxPreamble or TimeoutSignalSync interrupt.