Instruction manual

ManualsBrandsUltra Steel ManualsPower ToolAP00973S

ULTRA STEEL

1 8

VOLT

Cordless Power Tool Combo Kit

INSTRUCTION MANUAL

4 PIECE

CAUTION: Before using this product, read this manual and follow all Safety Rules

and Operational Instructions.

Go to www.ultrasteeltools.com to register your product.

Please read before returning this product to store for any reason.

If you have questions or experience a problem with your Ultra Steel purchase,

go to http://www.ultrasteeltools.com for instant answers 24 hours a day.

If you can’t nd the answer or don’t have internet access, call 1-800-840-

7856 from 8 a.m. to 5 p.m. Eastern time Monday through Friday.

AP00973S

The RBRCTM Seal (Rechargeable Battery Recycling Corporation) on the

nickle-cadmium battery (or battery pack) indicates that the cost of

recycling the battery or battery pack have already been paid by Ultra

Steel. In some areas, it is illegal to place spent nickle-cadmium batteries in

the trash or municipal solid waste stream and the RBRC program provides an environ-

mentally conscious alternative.RBRC in cooperation with Ultra Steel and other battery

users, has established programs in the United States and Canada to facilitate the

collection of spent nickle-cadmium batteries. Help protect our environment and

conserve natural resources by contacting your local recycling center for information on

where to drop o the spent battery, or call 1-877-2-RECYCLE.

THE RBRC

SEAL

FULL ONE YEAR HOME USE WARRANTY

Ultra Steel warrants this product for one year against any defects in material or

workmanship. The defective product will be replaced or repaired at no charge in

either of two ways:

1) Return the product to the store in which it was purchased - this will result in an

exchange only.

Returns should be made within the time frame of the retailer’s policy for exchanges

(usually 30 to 90 days after the sale). Proof of purchase is required. Please check with

the store from which your purchase was made to determine policy regarding returns

2) Send the product to Ultra Steel for repair or replacement (whichever Ultra Steel

determines is the best option) and include your proof of purchase.

legal rights and you may have other legal rights which vary from state to state

or province to province. For questions, call Ultra Steel at 1-800-840-7856.

This product is not intended for commercial use.

SERVICE INFORMATION:

For technical advice, repair, or genuine replacement parts,

call 1-800-840-7856 or visit www.UltraSteeltools.com

FREE WARNING LABEL REPLACEMENT:

If your warning labels become illegible or are missing, call 1-800-840-7856 for free

replacement.

Ultra Steel is a registered trademark of and distributed by Test Rite Products

Corporation, 1900 S. Burgundy Place, Ontario, CA. 91761, U.S.A.,

Made in China

Summary of content (17 pages)

PAGE 1
THE RBRC TM SEAL The RBRCTM Seal (Rechargeable Battery Recycling Corporation) on the nickle-cadmium battery (or battery pack) indicates that the cost of recycling the battery or battery pack have already been paid by Ultra Steel. In some areas, it is illegal to place spent nickle-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools in damp, wet, or poorly lit locations. Don’t expose your tool to rain. Keep the work area well lit.
PAGE 3
SPECIFICATIONS Cordless Drill Model No.: AP00965G Voltage: 18 volts DC No Load Speed 0-350/0-1100 RPM Variable Speed Trigger With Electric Brake 3/8 In. Keyless Chuck 22 + Position Adjustable Torque Clutch Built-in LED Work Light Built-in Magnetic Holder Conforms to UL STD No. 60745-1, UL STD No. 60745-2-1, UL STD No. 60745-2-2 60745-1-07, CAN/CSA-C22.2 STD No. 60745-2-1-04, CAN/CSA-C22.2 STD No. 60745-2-2-04 Cordless Sander Model No.
PAGE 4
OPERATING NOTES FOR BATTERY PACK 1. Battery must be fully charged before the first use. Batteries will reach full performance after about five charge/discharge cycles. 2. Always have drill rotation switch in neutral position when removing or inserting battery to avoid unintentional starting. 3. To remove battery pack, press the lock spring buttons and pull out. 4. To insert, simply push pack in until lock spring clicks. 5. To charge, plug the charger’s AC input plug into a 120V 60Hz household current.
PAGE 5
CHANGING THE BLADE 1. Always grasp the saw with both hands on the handles and push the saw through the material. 2. Be sure there are no nails or any other foreign objects in, on the work piece, or in the path of the blade. They could cause damage to the saw blade, injury from kickback or even injury from flying debris. 3. Make sure the work piece is properly supported at all times. Plan so that it is properly supported during the cut. 4. Whenever possible, secure the work piece with clamps or in a vise.
PAGE 6
• Keep the tool clean using a soft damp (not wet) cloth. Do not use solvents on the plastic parts. • Lubrication is not necessary. After long use, have an authorized service center maintain and lubricate the tool. • Should the chuck require replacement: 1. Keep the tool housing and handle clean and free of oil and grease using mild soap petroleum-based products, etc., contact plastic parts of the housing.
PAGE 7
PARTS LIST FOR CIRCULAR SAW Item English Name Qty Unit Item English Name Qty Unit 1 Screw M6x16 1 PCS 23 Gear box(rear) 1 PCS 2 Upper platen 1 PCS 24 Screw M4x12 2 PCS 3 Saw blade 1 PCS 25 Small gear 1 PCS 4 Lower platen 1 PCS 26 Motor 1 PCS 5 Screw M4x12 3 PCS 27 Right housing 1 PCS 6 Adjustable guide 1 PCS 28 Screw ST3.9x16 12 PCS 7 Spring 1 PCS 29 Motor cover 1 PCS 8 Fixed guide 1 PCS 30 Screw ST3.
PAGE 8
PARTS LIST FOR CORDLESS DETAIL SANDER English Name PARTS LIST FOR CORDLESS LIGHT Qty Unit Item English Name Qty Unit Item Qty Unit Item Qty Unit 1 Logo label 1 PCS 17 Driving gear 1 PCS 1 Housing (support ) 1 PCS 14 Right middle cover 1 PCS 2 Screw 9 PCS 18 Motor 1 PCS 2 Left head cover 1 PCS 15 Battery clip assembly 1 SET 3 Housing cover 1 PCS 19 Housing support 1 PCS 3 Light head 1 PCS 15.
PAGE 9
EL SELLO RBRC TM La Junta RBRCTM (Rechargeable Battery Recycling Corporation) en el níquel-cadmio (ni a la batería) indica que el costo de reciclaje la batería o la batería ya han sido pagados por Ultra Steel En algunas áreas, es ilegal poner pasó hidruro de cadmio las baterías usadas a la basura o desechos sólidos municipales y el programa de RBRC proporciona un ambiente mental consciente alternativa.
PAGE 10
INSTRUCCIONES ADVERTENCIA: Al usar herramientas eléctricas, máquinas o equipos, siempre se deben seguir precauciones básicas de seguridad para reducir el riesgo de incendio, choque eléctrico, y lesiones personales. LEA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR ESTA HERRAMIENTA 1. MANTENGA LIMPIA EL ÁREA DE TRABAJO. Zonas saturadas invitar a las lesiones. 2. CONSIDERAR ÁREA DE TRABAJO MEDIO AMBIENTE. No utilice herramientas eléctricas en lugares húmedos o mal iluminados.
PAGE 11
ESPECIFICACIONES CALIFORNIA PROP 65 Y OTRAS ADVERTENCIAS ADVERTENCIA: Algunos polvo creado al lijar, serrado, esmerilado, taladrado y otras actividades de construcción contiene sustancias químicas conocidas en el estado de California como causantes de cáncer, defectos de nacimiento u otros daños reproductivos.
PAGE 12
ESPECIFICACIONES NOTAS SOBRE EL FUNCIONAMIENTO DE LA BACTERIA Sander Inalámbrico Modelo Número.: AP00963G Tensión: 18 voltios CC Velocidad sin carga 4400 RPM Interruptor de activación 3-1/2 in. Zapata lijadora A B C Conforms to UL STD No. 60745-1, UL STD No. 60745-2-4 A B C 60745-1-07, CAN/CSA-C22.2 STD No. 60745-2-4-04 D E Base de lijado Interruptor Empuñadura revestida de goma Pack de batería Botón de bloqueo de la batería Linterna Inalámbrico Modelo Número.
PAGE 13
2. Cuando se presiona hacia dentro de la derecha a la izquierda, la rotación es inverso (Contrario a las agujas del reloj). 3. Cuando en la posición central, esté bloqueado en posición neutra y la activación está bloqueado. 4. No empuje el sentido de rotación hasta que el chuck deja de girar REGULADOR PAR Este es un 22+ posición dial situado antes de la fijación. 1.
PAGE 14
CAMBIO DE LA CUCHILLA PRECAUCIÓN: no coloque las manos directamente en frente de, detrás de, o por debajo de la hoja de sierra para cortar. 1. Use la llave que se incluye con el kit. 2. Pulse el botón de bloqueo del eje 3. Gire la tuerca hacia la derecha para aflojar. 4. i Extraiga el módulo de alta densidad y sustituirla por la nueva hoja.ga el módulo de alta densidad y sustituirla por la nueva hoja. 5. Volver a colocar la tuerca y gire a la izquierda para apretar. NOTA: 1.
PAGE 15
SÍMBOLO ADVERTENCIA: Algunos de los siguientes símbolos pueden aparecer en la herramienta. Estudio estos símbolos y aprender sus contempladas. Interoeretation adecuada de estos símbolos para permitir más eficiente y segura de esta herramienta. LISTA DE PIEZAS PARA EL TALADRO INALÁMBRICO Qty Unit Item Nombre en Inglés Qty Unit 1 de dos bits 2 PCS 13.1 Interruptor 1 PCS 2 clip 2 PCS 13.2 Línea 2 PCS 3 etiqueta con el logotipo 1 PCS 13.
PAGE 16
LISTA DE PIEZAS PARA SIERRA CIRCULAR Item Nombre en Inglés Qty Unit Item Nombre en Inglés Qty Unit 1 Tornillo M6x16 1 PCS 23 Caja de engranajes Parte trasera) 1 PCS 2 Upper platen 1 PCS 24 Tornillo M4x12 2 PCS 3 Hoja de sierra 1 PCS 25 Engranaje pequeño 1 PCS 4 Lower platen 1 PCS 26 Tornillo del Motor 1 PCS 5 Tornillo M4x12 3 PCS 27 Caja Derecha 1 PCS 6 Guía ajustable 1 PCS 28 Tornillo ST3.
PAGE 17
LISTA DE PIEZAS PARA CORDLES DETALLE SANDER Qty Unit Item Qty Unit Item Nombre en Inglés Qty Unit Item Etiqueta 1 PCS 17 Engranaje de 1 PCS 1 Apoyo de la caja 1 PCS 14 Cubierta intermedia derecha Tornillo 9 PCS 18 Motor 1 PCS 2 1 PCS 15 3 Tapa de la caja 1 PCS 19 Apoyo de la caja 1 PCS 3 Tapa de culata izquierda Cabezal de luz 1 PCS 15.