Instruction manual

58
AILE
0
S.TRIM
Function Being ProgrammedIndicates Channel for Which
Sub-Trim is Being Adjusted
Sub-Trim Value for Indicated Channel
(Range ±125)
: Aileron (Right Aileron)
: Elevator
: Rudder
: Gear (Left Aileron – Aileron 1)
: Auxiliary 1
(Right Flap Channel for Dual Flaps)
: Auxiliary 2
(Left Flap Channel for Dual Flaps)
AILE
ELEV
RUDD
GEAR
AUX1
AUX2
Increases
Sub-Trim Value
Decreases
Sub-Trim Value
Resets Sub-Trim
Value to 0%
+
CLR
–
Channel Selection
UP
CHDN
THRO: Throttle (Spoiler)
AILE1: Aileron (Right Aileron)
ELEV: Elevator
RUDD: Rudder
AIL2: Gear (Left Aileron – Aileron 1)
FLAP: Auxiliary 1
(Right Flap Channel for Dual Flaps)
AUX2: Auxiliary 2
(Left Flap Channel for Dual Flaps)
CONTINUED
Section 19: Programming Guide —
JR XP783/XP347/XP388S
Step 7. Adjusting the sub trims: Turn on the transmitter
and receiver and center the trims. Move the flap switch in the
upper position. Now reposition all the servo arms so that all
the control surfaces are as close as possible to their neutral
positions. In System Setup mode, press the Up key until the
“S.TRIM” screen appears. Now press the Channel key to access
the desired channel and press the (+) or (-) key to perfectly
center each control surface.
AILE
R 100
%
T.ADJ
Function Being ProgrammedIndicates Channel for Which Travel
Adjust is Being Programmed
Travel Value Adjust
(0 –150%)
Servo Acting Direction
: Aileron (Right Aileron)
: Elevator
: Rudder
: Gear (Left Aileron – Aileron 1)
: Auxiliary 1
(Right Flap Channel for Dual Flaps)
: Auxiliary 2
(Left Flap Channel for Dual Flaps)
AILE
ELEV
RUDD
GEAR
AUX1
AUX2
Increase or Decrease
Travel Value
Resets Travel Adjust
to 100%
+
CLR
–
Channel SelectionTo Elevator to
Flap Mixing
To Sub-Trim
UP
CHDN
THRO: Throttle (Spoiler)
AILE1: Aileron (Right Aileron)
ELEV: Elevator
RUDD: Rudder
AIL2: Gear (Left Aileron – Aileron 1)
FLAP: Auxiliary 1
(Right Flap Channel for Dual Flaps)
AUX2: Auxiliary 2
(Left Flap Channel for Dual Flaps)
Note: The throttle is referred to as “SPOI” in the glider mode.
Step 8. Setting Travel Adjust: Press the Up key until the
“T.ADJ” screen appears. Pressing the CH key will allow access
to each channel. Adjust the travel of each channel to the throws
shown below using the (+) or (-) key. Move the corresponding
control stick in the desired direction to adjust the travel amount
in that direction.
Note: To get the most performance out of your Ultra Stick
™
,
long servo arms (1") are recommended. This provides
for large control throws for more aggressive maneu-
vers. To achieve the control throws listed below, long
servo arms may be necessary.
Note: Adjust the right flap travel first, then the left flap.
Throttle — Full open to full closed with trim
(Referred to as “SPOI” in GLID mode)
Aileron — 1
1
/4" up, 1
1
/4" down
Elevator — 1
7
/16" up, 1
7
/16" down
Rudder — 3" right, 3" left
Full Flaps — 1
5
/8" down