Spindle

DETAIL A
O-RING GLAND
Tie Down Engineering
5901 Wheaton Drive Atlanta Georgia 0336
Unspecified
Tolerances:
Decimal ` 0.1
Decimal ` .02
Decimal ` .010
Angles ` 1.0 ~
Holes ` .008
Rev.:
Part No.:
Material:
Part Name:
Date:
Design:
Drawn:
Approved:
CO NFIDENTIALITY NO TICE: THIS DRAWING AND ALL INFORMATION CONTAINED WITHIN IT ARE
THE PROPERTY OF TIE DOWN ENGINEERING, ATLANTA, GA 30336. ALL RIGHTS ARE RESERVED.
SPINDLE, 1350#, S/L, (TORS.)
5/18/2009
C1040-1045 HR STEEL - 1.50 D. x 8.24 L.
80047
DLM
3
Sht.:
1 of 1
A
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
C1040-1045 HR STEEL - 1.50 D. x 8.24 L.RR11211
O-RING, 1 1/16 ID x 1/16 (AS568-023) BUNA-N
17441Installed12
WEAR SLEEVE, 1.25 D. STAINLESSBAWS12513
8.18
.620
.601
3.107
3.399
4.21
.250
.250
.094
.055
5°
.25
R.012
R.005
n 1.490
MIN. CLN. UP
MIN.
1.390
1.0620
n
1.0610
1.215
n
1.209
10° 0'
-
0° 0'
0° 2'+
.010 x 45° CHAMFER
.063 x 45° CHAMFER
.04 x 45° CHAMFER
R.080
R.040
R.030
R.015
1-14 UNS - 2A
1-14 UNS - 2A
32
125
100
n .166 (No. 19 DRILL) THRU ON CENTER
n .166 (No. 19 DRILL) THRU ON CENTER
4.19 w/WEAR SLEEVE3.126
1.253
1.247
n w/WEAR SLEEVE
20
10
1
3
2
TURNING CENTER
POST TURNING CENTER MACHINING & ASSEMBLY
REVISION HISTORY
REV DATE BY EFFCTV DESCRIPTION
1 05/08/09 DLM R.C.
8.18 (8.50), 4.19 (4.395), .250 (.375), .874 (.989), .752 (.867), .620 (.750), 1.253/1.247 (1.250/1.235),
OFFSET DRILL "C" HOLE .25 FROM CENTER
2 5/10/2010 DLM R.C.
+WEAR SLEEVE FEATURE & DETAILS; UPDATED WEIGHT CLASS TO 1350# (1250#)
3 3/31/2015 JEP R.C.
SPINDLE MACHINED FROM STOCK MATERIAL RR112 (80094)
2
1
1
NOTES:
1. ALL DIMENSIONS ARE IN INCHES.
2. SIZE O.D. OF SPINDLE MACHINING TO I.D. OF WEAR SLEEVE FORE PRESS FIT.
3. INSTALL O-RING IN GLAND w/LUBRICANT, THEN PRESS FIT WEAR SLEEVE.
4. REMOVE ALL BURRS FROM DRILLED HOLES.
5. BREAK ANY SHARP EDGES w/MIN. RADIUS OR CHAMFER.
2
2
.86
.74
1
1
2
1
1
1
1
3.380
1
1
1
22
n .242 (SIZE "C" DRILL) x 4.38
.250
1
Ø.110 (No. 35 DRILL) TO AXIAL DRILLING
2
2
2
1
2
3