2-S Speed d Traiiler WinchW -2500 0Lb. C Capac city Owner’s Ma anual WA ARNING: Read R carefully and underrstand all ASSEMBLY AN ND OPERAT TION INSTRUCTIONS beffore operating. Failure to follow the sa afety rules an nd other bassic safety pre ecautions may resu ult in serious personal injury.
Thank you very much for choosing anUltra-Tow™product! For future reference, please complete the owner’s record below: Serial Number/LotDate Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This winch is designed for certain applications only.
Table of Contents Intended Use ..........................................................................................................................................4 Technical Specifications ......................................................................................................................4 Important Safety Information ...............................................................................................................4 Specific Operation Warnings ..........................
Intended Use This Ultra-Tow 2 Speed Trailer Winch is designed for multipurpose hauling and lifting operations. It has a fast speed for quick pull in and a low speed for increased mechanical advantage. The quick attach handle allows for an easy change from high speed to low gear for heavier loads. Pulling winches are best suited for boat trailers and other horizontal pulling applications which require the freewheeling feature of ratchet type winches. Technical Specifications Property Item No.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the winch. ⚠WARNING PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating the winch.
Do not use for overhead lifting. Do not lengthen the handle for additional leverage. Keep hands clear from the gear, drum and rolling cable. Always wear gloves when using the winch. Never leave winch unattended while supporting a load. Follow all instructions when replacing the cable of strapping. Always maintain a minimum of four (4) full turns of cable or strap around the drum of the winch. Never apply load to winch fully extended. Operate winch manually only.
1) Place pawl in reel out position. Reel the old cable all the way out by turning handle counterclockwise. 2) Loosen the nut and remove the old cable from underneath the cable clamp. 3) Remove the old cable. 4) Route new cable end over bushing and through the hole to the outside of the drum. 5) Install the cable under the cable clamp. 6) Tighten the nut securely. 7) Placepawl in reel in position, then reel the new cable onto drum by turning the handle clockwise, being careful not to allow kinking.
Assembly Instructions Insert the quick attach handle until it clicks into place. Fast speed for quick pull in, low speed for increased mechanical advantage. The quick attach handle easily transitions from high speed to low gear for heavier loads. Before Each Use ⚠WARNING CHECK BEFORE USE Check the safety devices and the safe condition of the product. Check whether there are any visible defects. Check whether all parts of the product are firmly attached.
4. Put the ratchet switch on the higher position and turn the crank handle clockwise to pull. Put the ratchet switch on the lower position and turn the crank handle counterclockwise torelease. 5. When finished, attach the hook to the paw bushing. Maintenance This winch has been fully lubricated at the factory; but, for continued smooth performance and increased life, occasional greasing of gears and reel shaft and an occasional drop of oil on drive shaft bearings are recommended.
Troubleshooting ⚠WARNING Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance.
Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 Part Number 1 2-12 13 14 15 16 17-23 24 25 26-27 28-30 Item Description Base Reel Assembly Locknut Reel Shaft Shaft Bushing Cap Nut Ratchet Kits Drive Shaft Rear Cover Cap Nut Handle Kits Quantity 1 1 1 1 1 1 1 1 1 2 1 Remark Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Ultra-Tow product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one yearfrom date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.