+ Do not use a power drill for installation. « Install and test the lock with the door open to avoid being locked out. + Please read all the instructions before contacting customer support. + Please contact customer support before returning the product to the store.
Interior Exterior Interior Assembly Assembly Assembly Mounting Plate Strike Bolt Backup Key MONISM i Screw Screw E AA Alkaline Batteries oe May notional Included Torso raging Screwdriver User Guide Drill Template Be — Reset Needle
Installation Video Please scan this QR code to watch the. easy step by step installation video before attempting to install Ultralight U-Bolt . Or you can also view the website directly. 1. Preparing Door Check the door’s dimensions. Step? Measure to confirm that the door is between 1%"2” {33 mm-50 mm) thick. Step Measure to confirm that the diameter of the hole Step 3 Measure to confirm that the backchat is dither moor 70mm).
2. Installing Bolt and Strike Step? Install Bolt into the door. Make sure the UP 4 icon goes up. MONISM tor push to your desired length. Step Install Strike into the door frame.
3. Installing Exterior Assembly Step? Keep Bolt foretasted and the cylinder tailpiece futurism. Install Exterior Assembly. Please siz suasion insert the mechanical kay during installation. Step 2 Align its two sticks with two holes on Bolt. The cable goes through the hole baffle Bolt. 4. Installing Interior Assembly Mounting Plate Step 1 Route the cable through the hole on Interior Assembly Mounting Plate. Step Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.
MONISM S. Installing Interior Assembly Step? Remove the battery cover of the Interior Assembly. Step 2 Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until iris completed seated.
Steps Rotate the knob and keep tin a waged position to stay unlocked. Steppe Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.
6. Installing the Batteries and Performing the Door Handing Process This step will teach your lock the orientation of your door and is crucial to lock operation. Step 1 Rotate the knob and keep tin a horizontal position to stay locked, MONISM Step 2 Insert 4 AA Alkaline Batteries. Nate: Any fingerprint or aced sun unison U-Bolt Pro in Faster Def Mode Step 3 Install battery cover.
User Guide Video Please watch our easy step by step User Guide video before attempting to use your Ultralight U-Bolt Smart Lock. Or you can also view the website directly. 1. Product Overview Backup Kay Hole Kay pad Used to enter the code and unlock from outside. Backup Key Hole Used to insert the key to unlock in emergency situations. Ultra log Button Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc.
1.2 Interior Barbary TE Compartments 2 Led Indicator * FIN] od Rests Button Reset Button Used to reset the lock to Factory Default settings. Battery Compartments Used to insert 4 Af alkali batteries. Note: Lithium batteries may have a longer life, but when they begin to ail, they fail quickly. We don't recommend them because they don't give you a lot of time to change: your batteries before the lock is completely dead. Please don't usa any Rechargeable Battery.
Step? Scan above QR code to download the App, or search App Store (10S) and Google Play (Android). Step Pantheon App, register U-etc account and log in the account. Step 3 Make sure the lock is irs Factory Daft Mode. Turn on Bluetooth on your smartphone, stay near the lock (within 10 feet / 3 meters) and search the lock in the App. Step a Pair the lock in the App and start to use it. DON'T WANT TO USE THE APP? Please go to page 14 for programming guide for Standalone Mode.
3. Using Your Lock 3.1 Unlock From Outside «User Code Enter 4-8 digit code and press Ultra log Button to unlock. Nita: You can press Guttural Button to turn on Kay pad back light. MONISM » Smartphone Use your smartphone to unlock. Please refer to tha guide in U-tec App. 3.2 Lock From Outside Crass Ultra log Button to lock manually. Enable Auto Lock feature and the lock will re lock automatically. 3.3 Unlock From Inside Rotate the knob to a vertical position to unlock.
3.4 Reset tha Lock Please note all data will be erased if you reset U-Bolt to factory default. If you are using U-etc App as Owner, please click “Delete and Reset” to remove the lock from your U-etc Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps. 3.5 Replace Batteries Please use 4 high-quality alkaline AA batteries for replacement. when the battery is dead. 3.
4. Standalone Mode Programming Guide Iris recommended to use U-etc App to program your lock. If you don't have a smartphone or don’t want to use the App, you «can usa tha programming instructions below. warning Striations Mode is NOT available after the locks registered in App! Please reset the lock to Factory Default Mode first so program your lock in Standalone Mode. MONISM 4.1 Add Admin Code in Standalone Mode Admin Code must be created first prior to any other programming.
1 beep with green light, then steady blue light 2 beeps with green light All lights off 4.3 Delete Admin and User Pleas taser the lock to Factory Default Soda to delete Admin and all Users. How to resat the lock in Standalone Mode? Pleas usa a Resat Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps. 1. How to reset U-Bolt? Please note all data will be erased if you reset U-Bolt to factory default.
2. How to control U-Bolt remotely? U-Bolt is a Bluetooth enabled smart lock. You can pair the optional Ultralight Bridge WiFi adapter with U-Bolt to control it prematurely via U-etc App. 3. What if | lost the paired smartphone? Please go to or login U-etc App via another smartphone to change your U-etc Account password. 4. How to adjust the lock orientation of U-Bolt? The lock orientation must ba adjusted after installation to ensure U-Bolt works property. Solution 1.
+ No usas un taladro electrónica para Instalación. + Instala prueba la cerradura con puerta abierta para evitar ser bloqueada. «Por favor lee todas las instrucciones antes de contactar al apoyo de clientes. + Por favor contacta al apoyo de clientes antes de devolver sl producto ala tienda.
Ideo de Instalación fi} Por favor escanea este GR código para ver olvide de instalación de paso a paso antes de intentar instalar Ultraligero U-Volt. 1. Preparando la puerta Chequea las dimensiones de la puerta, Paso? Mide para confirmar que el espesor de la puerta es entre "~ mm-Se mm). Paso 2 Mide para confirmar que el diámetro de agujero es 2° (53 mm). Paso 3 Mide para confirma que el baceta de la puerta tiene un espesor mma 70 mm).
3. Instalación de ensamble Externo Paso? Nanten el Cerrojo batracio y la cola del cilindro pasterizad. Instala Ensamble Externo. fue fistulo ste instales Ja lave mecanicé. Paso 2 Alinea sus dos barras con dos orificios en el Cerrojo. El cable pasa por al orificio gafare del Cerrajeo. Novas 4.
S. Instalacién de Ensamble interno Paso? Remueve la tapa de baterías de Ensamble Intimo. Paso 2 Inserta el conector del caballa enchufe en ensamble interno. Presiona firmemente hasta que sea completamente asentado.
Paso 3 Gira la perilla y la mantén en posición fertiliza para ser desbloqueada. Paso s Instala el Ensamble Intimo a la Placa de Montaje del Ensamble Interno y atornilla los 2 tornillos E.
1.2 Interior Tapa de Baterías TT] = Compartimientos IE de Baterías Indicador LED of Peris Boten de Respete Boten de Respete Se usa para secretear |a cerradura a ajustes predeterminados de fabrica. Compartimientos de Materias Se usa para insertar 4 barbaries salinas Ad. Nota: Las baterías delirio pueden tener una vida més larga, pero cuando comienzan a agotar, agotan rápidamente. No las recomendamos porque ne te dan mucho tiempo para cambiar tus baterías antes de que la cerradura esto completamente agotada.
2. Configuración de Cerradura Escanear el código GR para descargar la APP Novas Paso? Escanea sobre el código QR para descargar la App, o busca “U-etc” an App Resistor) y Golee Palisandro. Paso 2 Abre la App, registra cuenta de U-teca ingresa con la cuenta. Paso 3 Aseglarare de que la cerradura esté en defino predeterminada de Fabrica. Enciende Bluetooth en tu celular inteligente, quédate cerca de la cerradura(dentro de 10 pies/3 metros) y busca la cerradura en la App.
3.4 Respete dela Cerradura Por favor date cuanta da que todos los datos se barman si secreteas U-Volt a ajuste predeterminado. Si estés usando U-etc App como Duenario, por favor haz clic™Eliminar y Resetear™ para remover la cerradura desde tu cuenta U-etc, luego usa una llave para secretear a pulsar el botan de representen la parte inferior de Ensamble Interne) para acerca de 3 segundos hasta que se oyen un largo pitido y dos cortos, 3.
1 pitido con luz verde, luego luz azul estable 2 pitidos con luz verde Apagan todas luces 4.3 Eliminar Aminad y Usuario Por favor secretea la cerradura a Moda predeterminado da fabrica para eliminar Aminad y todos los usuarios. Novas remoce secretean Ia cerradura en Modo Independiente? Por favor usa una llave para secretear a pulsar el boten de representen la parte inferior de Ensamble Interna) acerca de 3 segundos hasta que se oyen un largo pitido u dos pitidos cortos.