Instructions / Assembly

ManualsBrandsUnbranded ManualsOutdoorsBradley Black Jumbo Slat Wood Outdoor Patio Rocking Chair

1200 SIDE TO SIDE PORCH ROCKER

ASSEMBLY INSTRUCTIONS

Thank you for purchasing a quality select hardwood rocking chair. Your chair comes with a rich heritage

and will become a treasured family heirloom. If you should have any comments or questions please call the

toll-free number below between 8:00 AM and 5:00 PM CST Monday through Friday. Again, we appreciate

your business and hope you get many years of enjoyment from this chair.

NOTICE: The Rocking Chair product that you have purchased requires some assembly. As with all furniture,

proper assembly is necessary for the safe and comfortable use of your rocker. Hinkle Chair cannot be responsible

for any damage or injury that results from improper assembly of the chair. Please read and follow these instructions

carefully and in sequence. If you have any questions please call The Hinkle Chair Company helpline (800) 251-3025

or contact us on our website at www.hinklechair.com.

Summary of content (11 pages)

PAGE 1
200 SIDE TO SIDE PORCH ROCKER ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality select hardwood rocking chair. Your chair comes with a rich heritage and will become a treasured family heirloom. If you should have any comments or questions please call the toll-free number below between 8:00 AM and 5:00 PM CST Monday through Friday. Again, we appreciate your business and hope you get many years of enjoyment from this chair.
PAGE 2
ROCKING CHAIR ASSEMBLY INSTRUCTIONS D-L E C-1 D-R C-2 F BUTTONS NAILS HEX SCREWS SEAT SCREWS WRENCH A B PARTS INCLUDED: 1 – Chair Back (A) 10 – Wooden Buttons 1 – Chair Seat (B) 10 – Hex Head Screws 2 – Back Spindle (C-1) 4 - Seat Screws 3 – Front Spindles (C-2) 1 - Hex Wrench 2 – Rocker Sides (D-L/D-R) (facing chair from front) 2 - Runners (E) 1 - Headrests (F) TOOLS REQUIRED FOR ASSEMBLY: (NOT INCLUDED) Rubber Hammer or Standard Hammer (using folded towel/or heavy cloth to protect the finish) Phi
PAGE 3
** Attention/Stop** Hinkle Chair Company has made every effort to provide you with a ready-toassemble product that has the same quality as our fully assembled rocking chairs. In the unlikely event that there are incorrect, missing parts, or the parts become damaged during shipping, following the instructions below will protect you(The Customer) from accepting responsibility for a product that is damaged or incomplete. 1st) Inspect all parts for any imperfection that might have occurred during shipping.
PAGE 4
STEP 1: __________________________________________ ______________________________________________ Place right side of rocker D-R on cardboard shipping box with mortised holes facing up. Insert the front spindles C-2 into the pre-drilled hole in the front post. Note: these are marked and place the two larger spindles in the bottom. Tap in with hammer. Fig. 1 Pick up Chair Back A and insert in the mortises in the . Chair side D-R. Note: leave top mortise open for Headrest F in a later step. Fig. 2 Fig.
PAGE 5
STEP 2:________________________________________________________________________________________ Insert Seat B, below the arm and above the top Spindles. The Seat B is marked front and back. You will not be attaching the Seat B at this time, but will not be able to insert it after this step Fig. 5 Place left side of rocker D-L over the tenons that are facing up and align. Try to get most tenons partially started into mortises. Gently tap down.. Fig. 6 Fig. 5 Fig.
PAGE 6
STEP 2: _________________________________________________________________________________________ Continue to tap the Rocker Side D-L down forcing the mortises down on the tenons. It may take a few times to get all completely inserted into mortises. Fig. 8 Fig. 8 STEP 2:____________________________________________________ _____________ _______________________ Move to the front and begin tapping the front post down. onto the Front Spindles C-2. Once all of the tenons are .
PAGE 7
STEP 3: _________________________________________________________________________________________ Again beginning at the top, place a Hex Screw into the pre-drilled hole and thread the Hex Screw in with the Hex Wrench provided. Note: Do not fully tighten until all Hex Screws have been inserted. Fig. 10 Fig. 10 STEP 3:____________________________________________________ _____________ _______________________ Place the next Hex Screw on the next pre-drilled hole down on the post. Again, do not fully tighten.
PAGE 8
STEP 3: _________________________________________________________________________________________ Move to the front post and continue the process. Complete for all five Hex Head Screws. Fig. 12 Fig. 12 STEP 4:____________________________________________________ _____________ _______________________ Rotate the upper side spindle in Rocker Side D-L until the pre-drilled hole is at a 45 degree angle. Start the Seat Screw into the pre-drilled hole and align with the pre-drilled hole in the bottom of the seat.
PAGE 9
STEP 5: _________________________________________________________________________________________ Place Runner E onto tenons on the bottom of the back and Front post. Note: There are pre-drilled holes in the side of the Runners E for the Nails that are provided. These predrilled holes should face to the inside of the rocker. Once aligned tap the runner fully onto the tenons. Fig. 14 Fig.
PAGE 10
STEP 6: _________________________________________________________________________________________ Go back through and fully tighten all 10 Hex Head Screws and the 4 Seat Screws. Be careful not to over tighten. Fig. 16 Fig. 16 STEP 6:____________________________________________________ _____________ _______________________ Place a Button in each of the pre-drilled holes and push in to get started. Use a hammer to gently tap the button into the pre-drilled hole.
PAGE 11
CARE TIPS LISTED BELOW ARE SOME TIPS TO HELP KEEP YOUR FURNITURE LOOKING NEW. To preserve the finish on stained or pure white furniture it is highly recommended that they either be placed indoors or in a protected environment such as a covered porch. In any case the finish will last longer and look better if kept out of direct sunlight and blowing rain. The finish on this furniture will last for a lifetime if used indoors. This furniture is not intended to be used in an unprotected environment.