62 537 Roanoke 48 in Ceiling Fan Owner’s Manual Roanoke Ventilador de Techo de 1,22 m Manual del Propietario
Roanoke by Hampton Bay ®
48” Roanoke Ceiling Fan by Hampton Bay Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 162-537 Unpacking Your Fan . . . . . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: A 2 5 1 B 8 3 C 6 9 7 4 1. 2. 3. 4. 5. Set of blades (5) Mounting bracket Fan motor assembly Blade arms (5) Switch housing WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 6. 7. 8. 9. Light plate Glass shade Pull chains and fobs (2) 40 Watt candelabra bulbs (3) A. Blade Attachment Hardware (16 Screws with Rubber Washers) B.
Installing Your Fan Tools Required Figures 1 and 2 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters. Outlet Box Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Figure 3 Figure 1 Secure the outlet box directly to the building structure.
Hanging the Fan 1. Connect the ground conductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan (Figure 6). REMEMBER to turn off the power. Follow the steps below to hang your fan properly. 1. Attach the mounting bracket to the outlet box with two screws and washers provided with the outlet box. Make sure the bracket is tight and secured (Fig. 4). 2.
BLACK WHITE SUPPLY CIRCUIT Ground Conductor BLUE BLACK WHITE GREEN Outlet Box Green Ground Lead Ground to Fan Finishing the Fan Installation Remove the fan from the hook on the mounting bracket. Secure the fan assembly to the mounting bracket with four screws included with your fan. Be sure to tighten all screws.
Attaching the Fan Blades Screws with Rubber Washers 1. Attach blades to blade arms using three screws with rubber washers (Fig. 8). Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Repeat steps for the remaining blades. 3.
previously loosened and the one previously removed. (Figure 11) Blade Balancing (if fan wobble is present after fan is completely assembled) Touching Ceiling 3. Snap the wire connection plugs together. The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal.
Installing the Light Kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 1. While holding the light plate under your fan, locate two single white and blue wires in the switch housing labeled FOR LIGHT.
Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION. Turn on the power and check the operation of the fan. The pull chain controls the fan speed as follows: Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect as shown in Figure 13. This allows you to set your air conditioner on a higher setting without affecting your comfort. 1 pull - High 2 pulls - Medium 3 pulls - Low 4 pulls - Off.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. PROBLEM SOLUTION 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 48” MED. HIGH 120 WATTS RPM CFM 0.23 12 83 2094 0.39 34 150 4041 0.45 53 185 5114 N.W. G.W. C.F. 9.4 kgs (20.8 lbs) 10.7 kgs (23.6 lbs) 1.97’ These are approximate measures. They do not include Amps and Wattage used by the light kit.
Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
