Instructions / Assembly

ManualsBrandsUnbranded ManualsOutdoorsBradley Maple Slat Patio Rocking Chair

TRADITIONAL HARDWOOD

#200 SLAT ROCKER

ASSEMBLY INSTRUCTIONS

Thank you for purchasing a quality select hardwood rocking chair. This rocking chair is distributed by

the Hinkle Chair Company, a family-owned business that has made hardwood furniture in the same location in

Springfield Tennessee since 1834. Your chair comes with a rich heritage and will become a treasured family

heirloom. If you should have any comments or questions or need these instructions in Spanish, please call the

toll-free number below between 8:00 AM and 4:30 PM CST Monday through Friday. Again, we appreciate

your business and hope you get many years of enjoyment from this chair.

Espaňol: Si usted tiene cualquier comentario o preguntas o necesita estas instrucciones en espaňol por favor

yame al numero de llamada gratuita 1-800-251-3025 entre las horas de 8:00 AM y 4:30 PM hora central de

Lunes a Viernes.

NOTICE: The Rocking Chair product that you have purchased requires some assembly. As with all furniture,

proper assembly is necessary for the safe and comfortable use of your rocker. Hinkle Chair cannot be responsible

for any damage or injury that results from improper assembly of the chair. Please read and follow these instructions

carefully and in sequence. *To ensure proper assembly, pre-assemble the chair to identify all necessary components

and familiarize yourself with the assembly process. If you have any questions please call

The Hinkle Chair Company helpline (800) 251-3025

Summary of content (8 pages)

PAGE 1
TRADITIONAL HARDWOOD #200 SLAT ROCKER ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality select hardwood rocking chair. This rocking chair is distributed by the Hinkle Chair Company, a family-owned business that has made hardwood furniture in the same location in Springfield Tennessee since 1834. Your chair comes with a rich heritage and will become a treasured family heirloom.
PAGE 2
ROCKING CHAIR ASSEMBLY INSTRUCTIONS B C D E F G-L A Screws/Nails/Buttons H G-R PARTS INCLUDED: 1 – Chair Seat (A) Hardware: 1 – Chair Back (B) Nail pack w/4 nails 1 – Headrest (C) 4 Seat Screws 2 – Runners (D) 10 Buttons 2 – Back Spindles 19 inches (E) 10 Side Screws 1 – Front Spindle 22 inches (F) 1 Hex Wrench 1 – Chair Side left (G-L) 1 – Chair Side right (G-R) 2 – Turned Front Spindles (H) ******** ALL PERSPECTIVE OF LEFT AND RIGHT IS FROM FACING THE ********* THE CHAIR, NOT SITTING IN IT.
PAGE 3
**Attention/Stop** Please read before assembling this product! Hinkle Chair Company has made every effort to provide you with a ready-to-assemble product that has the same quality as our fully assembled rocking chairs. In the unlikely event that there are incorrect or missing parts or that parts become damaged during shipping, following the instructions below will protect you (The Customer) from accepting responsibility for a product that is damaged or incomplete.
PAGE 4
STEP 1: ________________________________________________________________ _______________________ Lay Chair Side Left (G-L) on the holes facing up on the shipping box to protect the finish. Install Front Spindle (F) Turned Spindles (H), and Back Spindles (E) as shown in Figure 1. H F FIG. 1 G-L Insert Chair Back (B) into mortises on Chair Side. Note that the bevel faces the rear of the chair. Figure 2. E FIG.
PAGE 5
STEP 2:________________________________________________________________________________________ Lay Chair Side (G-R) over corresponding spindles and components as shown in Figure 6. This step is much easier if two people align the corresponding spindles and components. Once the alignment is complete begin pressing down on the side to fully seat into all of the mortises and holes. A rubber mallet or a hammer with a heavy cloth to protect the finish may be used to tap all components in place. Figure 5 FIG.
PAGE 6
STEP 3: _________________________________________________________________________________________ Place Runner (D) onto the tenons at the bottom of the Chair Side. Once the Runner (D) is started onto the tenons gently tap the bottom of the runner until fully seated onto the tenon. Ensure that the pre-drilled holes face to the inside. Repeat for the other side. Figure 7. FIG.
PAGE 7
STEP 3: _________________________________________________________________________________________ With the Seat Screws provided, thread the screw into the pre-drilled hole and into the bottom of the seat. Hand tighten the screw until it is flush into the spindle and into the pre-drilled counter sink. Repeat for all four screws. Figure 9. FIG.
PAGE 8
CARE TIPS LISTED BELOW ARE SOME TIPS TO HELP KEEP YOUR FURNITURE LOOKING NEW. To preserve the finish on stained or pure white furniture it is highly recommended that they either be placed indoors or in a protected environment such as a covered porch. In any case the finish will last longer and look better if kept out of direct sunlight and blowing rain. This furniture is not intended to be used in an unprotected environment.