Instructions / Assembly

ManualsBrandsUnbranded ManualsDoor Chimes & KitsWhite 85 dB Wireless Plug-In Door Bell Kit with 1-Push Button with White Wireless Door Bell Push Button

HOMEDEPOT.COM

Please contact 1-855-556-1852 for further assistance.

Use and Care

Guide

Wireless Plug-In

Doorbell Kit

ITEM #1001 406 905 &

#1001 406 898

MODEL #216604 & #216605

Installation

ACTIVATING THE PUSH BUTTON

BATTERY

□ Remove the front cover of the push

button by inserting a ﬂat head

screwdriver in the slot on the bottom

of the button and pulling up slightly.

□ Remove the plastic tab from the

battery compartment to allow

connection to the terminal.

□ Snap the front cover onto the base by

ﬁrst hooking the tops together, then

snapping the base on.

□ Repeat for second button if

applicable.

PLUGGING IN THE CHIME

□ Plug the door chime into any outlet

in the house, ensuring it is within

the transmission range of the push

button location.

SYNCING THE CHIME AND PUSH

BUTTON

The chime and included push button(s)

already come synced. Follow the steps

below if you need to resync, or sync

additional push buttons.

□ Press and release the learning button

on the chime.

□ Immediately following, press and

release the push button to hear a

2-note tune. Press and release the

push button again within ﬁve seconds

to hear another tune. Continue

pressing and releasing the push

button until you reach the desired

tune. To set that tune, do not push the

push button for ﬁve seconds.

□ Follow the above steps for the

second push button if applicable.

216604-216605Inst.ai

Learning

mode

button

TOOLS REQUIRED

Phillips screwdriver Flat Head Screwdriver Drill

HARDWARE INCLUDED

216604-216605Inst.ai

Learning

mode

button

5/64” Drill Bit

216604-216605Inst.ai

Learning

mode

button

216604-216605Inst.ai

Learning

mode

button

(1) or (2) Adhesive

Stickers depending

on model

(2) or (4) #4 x 3/4 in.

Screws depending

on model

#4x3/4

#6x3/4

#4x1 White Zinc

#6x1 Self Tapping

ScrewHardware.ai

#4x3/4

#6x3/4

#4x1 White Zinc

#6x1 Self Tapping

ScrewHardware.ai

Summary of content (3 pages)

PAGE 1
Wireless Plug-In Doorbell Kit ITEM #1001 406 905 & #1001 406 898 MODEL #216604 & #216605 Use and Care Guide #4x3/4 TOOLS REQUIRED HARDWARE INCLUDED #6x3/4 #4x3/4 Phillips screwdriver Flat Head Screwdriver Drill #4x1 White Zinc #6x1 Self Tapping 216604-216605Inst.ai Installation 1 (1) or (2) Adhesive Stickers depending on model #6x3/4 Learning mode button 5/64” Drill Bit (2) or (4) #4 x 3/4 in.
PAGE 2
4 5 MOUNTING THE PUSH BUTTON □□ Remove the front cover from the base by following step 1. □□ Mount the push button base to a clean wall or door jamb with included screws or mounting tape. If mounting with screws, predrill a pilot hole through the push button base in the desired location using a 5/64 in. drill bit. □□ Snap the push button cover onto the base by first hooking the tops together, then snapping the base on.
PAGE 3
Troubleshooting Problem Possible Cause Solution Chime does not sound when push button is pressed. Push button battery has not been activated. Confirm the activation tab has been removed and the battery is seated properly in the button. The chime and push button are out of transmission range. Move the chime closer to the push button location. Ensure there are no metallic objects or concrete walls hindering the signal. Push button battery needs to be replaced.