Specification

Visit www.oatey.com for updates
TECHNICAL SPECIFICATION: Oatey No. 95 Lead Free Tinning Flux cleans, tins and fluxes most commonly soldered metals
including copper, brass, zinc, galvanized iron, lead and tin or copper-coated metals. No. 95 contains lead free solder powder
which helps draw in the solder wire. Fluxing is a critical step in the soldering process. No. 95 Tinning Flux provides superior
wetting properties for better solder flow and can be used with most soft solders. No. 95 Tinning Flux complies with CA & VT
lead content regulations.
NO. 95
LEAD FREE TINNING FLUX
PR
ECAUTIONS
Read all cautions and directions carefully before using this
product. Apply flux with brush- do not apply with fingers. Wash
hands thoroughly after use and before eating. Wear safety
glasses with side shields and rubber gloves. EYE AND SKIN
IRRITANT. HARMFUL IF SWALLOWED. VAPOR MAY BE
HARMFUL. Eye or skin contact may cause intense irritation and
injury. In case of contact with eyes or skin, flush with water and
seek medical attention immediately. If swallowed, DO NOT
INDUCE VOMITING. Drink water and call physician or poison
control center immediately. Ingestion of this product may cause
gastrointestinal distress. If inhaled, get fresh air and seek
medical attention if ill feelings persist. Keep container closed
when not in use. DO NOT REUSE EMPTY CONTAINER. KEEP
OUT OF REACH OF CHILDREN.
Refer to material safety data sheet for more information.
For emergency first aid help, call 1-877-740-5015.
COMMON APPLICATIONS
Oatey No. 95 Tinning Flux can be used to solder most commonly
soldered metals including copper, brass, zinc, galvanized iron and
tin or copper-coated metals.
Consult Oatey Technical Department for applications not
specifically referenced above.
INGREDIENTS
Petrolatum (8009-03-9)
Zinc Chloride (7646-85-7)
Ammonium Chloride (12125-02-9)
Tin (7440-31-5)
Copper (7440-50-8)
Bismuth (7440-69-9)
APPROVALS AND LISTINGS
NSF Listed Lead Free Flux
to Standard 61 Complies to CA & VT lead legislation
Meets Military Specification MIL-F-14256
1/2010
PHYSICAL/CHEMICAL PROPERTIES
Appearance Greenish-Gray Paste
Shelf Life 2 years from manufacture
date
Solder Temp. Range 400° F to 700° F
pH 3 - 4
DIRECTIONS FOR USE
Tinning Fluxes require only a small amount of flux
applied to the joint. Clean all surfaces before soldering.
Apply small amount of flux inside the fitting and outside
of the pipe. Heat to temperature required for soldering.
Do not overheat the piping. For small diameter piping,
direct the heat near the joint. For large diameter piping,
move the heat around the joint to ensure adequate
solder flow around the circumference of the joint. NOT
FOR USE WITH ALUMINUM, STAINLESS STEEL OR
MAGNESIUM. DO NOT USE ON ELECTRICAL PARTS.
When soldering process is complete, allow joint to cool
undisturbed. Remove any flux residual with a damp
cloth. Do not store No. 95 Tinning Flux above 100° F.
PRODUCT
NUMBER
DESCRIPTION PACK CARTON
WEIGHT
30374 1.7 oz. No. 95 Tinning Flux 12 4 lbs.
30374D 1.7 oz. No. 95 Tinning Flux – Display Carton 48 8 lbs.
30373 1.7 oz. No. 95 Tinning Flux with Brush – Carded 12 4 lbs.
53201 1.7 oz. No. 95 Tinning Flux with Brush – Carded without carton inserts 12 4 lbs.
30372 8 oz. No. 95 Tinning Flux 24 14 lbs.
30372D 8 oz. No. 95 Tinning Flux- Display Carton 24 15 lbs.
30375 16 oz. No. 95 Tinning Flux 12 14 lbs.
C-6