Instructions / Assembly

Fig 7
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified by
a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap from the end of the pole,
(that is pinched to a point), and place that end into the tree
stand. Be sure that the pointed end of the pole extends to
the bottom of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1);
including the contents of the poly-bag that is adhered to the
interior flap of the tree’s carton.
Contained in the poly-bag are RGB replacement bulbs and a remote
control which operates your tree's 102 function lighting capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An on/off push button foot pedal with cord and plug (Fig 6); which
is pre-attached at the lowest section of your tree (Fig 5).
The 6.5’ and 7.5’ trees will have (3) tree sections; (“A”, “B” and “C”; as
shown in Fig 5).
The 9’ tree will have (4) tree sections “A”, “B”, “C” and “D” contained in
two boxes.
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough room
for the tree’s pole from section “A” to be inserted into the
assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
Fig 6
Riverwoods, IL 60015 USA
www.santasbest.com
Made in China Printed in China
This is not a toy, for decorative use only.
Fig 2
REMOTE CONTROL OPERATION
The colors and functions of your pre-lit tree, as well as the
brightness control and timer feature are controlled solely
by the use of the remote control (Fig 7).
Brightness Control:
The brightness control button is located on the left side of the remote.
It offers three brightness settings (low, medium, high). Continually
press the button to reach your desired brightness level.
6H Timer:
The timer button is located on the right side of the remote. When set
to the "on" mode, the lights will flash Red 3 times indicating that the 6
hour timer has been activated. The tree will now remain on for 6 hours
and will automatically resume the last function 18 hours after shut off.
To turn off the timer, simply set to "off" mode. The lights will flash
Green 3 times.
If the tree is manually turned off while the timer is set, the timer will
shut off. If the tree is powered back on and the timer button is still set
to on, the timer will reactivate at that point and remain on for 6 hours.
CCT17
Patents pending.
NOTE: ALTHOUGH THE LED/RGB LIGHT STRINGS ON THE TREE
ARE RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION
OF THE TREE WITH THE LED/RGB LIGHTS IS FOR INDOOR USE ONLY.
2. If failure to light persists, press the on/off push button foot pedal;
as it may be in the “Off” mode.
3. If the top of the tree or another individual lettered section does
not illuminate, remove each section and then reinsert as
instructed, to ensure the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and firm
connection point. Downward force will be needed to ensure that
the electrical connection occurs.
4. In the case where your Remote Control selection is not in-sync
with the lighting displayed on your tree; simply power-off your
tree by the "ON/OFF" button located on your remote control, by
depressing your foot pedal to the off position or by unplugging
your tree from its outlet.
Once powered-off; re-plug back into the power outlet, which will
then reboot the synchronization of the lighting system.
5. Always inspect your tree for any burned out LED/RGB bulbs.
Although the tree will continue to remain lit even if a bulb burns
out, is loose or is missing; any burned out LED/RGB should be
replaced promptly to ensure the performance and life expectancy
of your tree.
NOTE: Replacement bulbs are provided; this is a specialty LED/RGB
bulb. Do not attempt to replace with a standard LED or
incandescent bulb. Should you require additional bulbs please
contact our customer service department.
NOTE: In order to determine which color replacement bulb is
needed; select “Steady” function and “Multi” color on your remote
control; to determine which color is absent.
6. A delayed response while switching between color selections on the
remote control is in no way a malfunction of the lighting. This is a normal
operating response due to the complexity of the technology.
All bulbs must independently receive their signal to alter to the
correct color selected. Some bulbs may receive their signals
quicker than others, hence a delayed receiver response may occur.
Again, this is innate of the technology and a normal response.
TROUBLESHOOTING
1. If the tree does not illuminate press the on/off button on your remote
control. If failure to light persists, the battery may need to be replaced.
Insert a standard 9 volt type battery (6F22, 6LR61 or 23F6-220);
aligning the appropriate ( +/- ) markings accordingly.
NOTE: The tree’s 102 function lighting capability is controlled solely
by the use of the remote control provided.
If the tree fails to light due to a damaged or defective remote control;
please resort to manual on/off push button foot pedal operation until
a new remote control can be provided through our customer service
center.
NOTE: DO NOT USE ANY ADDITIONAL LIGHTING OR
ORNAMENTATION THAT IS POWERED THROUGH THE LIGHT
BULB SOCKETS. DOING THIS MAY RESULT IN DAMAGE TO THE
LIGHTING SYSTEM OR MAY CAUSE PERSONAL INJURY;
THEREFORE VOIDING THE LIMITED WARRANTY PROVIDED
WITH THIS PRODUCT.
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the on/off push button foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight up
from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift each
section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A” from the
support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse downward,
due to the hinging, aiding in the packing of each section into the
storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold together;
placing in the storage container.
6. It is recommended to always store the tree in a cool, dry location
protected from excessive exposure to heat or sunlight.
NOTE: Store your remote control in a SAFE & DRY location and
remove the battery from remote control before storage.
DISASSEMBLY & STORAGE
Before operation, insert a standard 9 volt battery (6F22, 6LR61 or
23F6-220) into the remote by removing the sliding plate located on
the back of the remote, making sure to align the appropriate (+/-)
markings accordingly.
BELOW IS LIST OF FUNCTIONS AVAILABLE ON YOUR LED/RGB
TREE, BY USE OF THE REMOTE CONTROL.
a. All 14 color options can operate as either Steady, Twinkling, Firefly,
Slow Twinkle, Flash, Random Twinkle or Fireworks. There is also a Color
Changing (14 colors) and Slow Fade (14 colors).
PLEASE NOTE: When you are in the Color Changing or Slow Fade
function, you will be unable to use the color directional buttons. Press
the “Function” button which will allow you to select a different
function. You will then be able to access a single “Color” option.
b. SELECT FAVORITE - Gives you the ability to program 5 of your
favorite functions for easy recall.
To Program: Set the tree to the color and function you want to save,
then press “Select Favorite”. The tree will twinkle 3 times in blue,
indicating your selection has been saved. Repeat with next
color/function you want to save, for a maximum of 5 favorites.
To Play: Press the “Play Favorite” button one time. The #1 indicator
light will go on and the tree will switch to the first function you saved.
Press a second time to switch to your 2nd saved favorite and so on.
To Change: A maximum of 5 favorites can be stored. Select a 6th
favorite mode and your original 1st favorite will be removed, now
leaving your 2nd to 6th programmed favorites. Select a 7th favorite
and your 2nd favorite will be removed, leaving your 3rd to 7th
favorites and so on.
c. CYCLE FAVORITE - The tree will continually cycle through all 5 of your
favorite selections.
d. DEMO - The tree will continually cycle through all 100 functions.
Fig 3
7. On/off push button foot pedal operation:
The on/off push button foot pedal is intended to provide basic
manual on/off operation only; and therefore cannot provide
the remote control 102 function lighting capability.
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contains an on/off push
button foot pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert the
plug into a working electrical outlet.
10. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
11. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
12. Now gently guide the branches of section “B” downward into
place.
13. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is completely
assembled. Each section of the tree is labeled in alphabetical
order beginning from the bottom to the top.
8. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
9. Remove the protective plastic cap from the end of the pole
on section “B”; insert that end onto the top of the pole of
section “A” (Fig 4).
Fig 4
EZ-POWER™ TECHNOLOGY
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining sections
to light up automatically, upon a firm insertion of each
lettered section (Fig 5).
NOTE: If the tree is powered off by the use of the push
button foot pedal, remote control or by unplugging it from
the electrical outlet; when powered back on the tree will
resume the memory of the last lighting function selected
with the remote control.
Thank you for your purchase of this pre-lit & pre-shaped
Christmas tree.
With proper use and care, this tree will provide years of
trouble-free enjoyment.
Please follow the instructions below in order to effectively
assemble and disassemble your tree.
In the event that you should encounter any issues during the
assembly of your tree; please refer to the “Troubleshooting”
portion of this manual or call our toll free customer service
number at 1-888-831-6656, and a trained representative will
assist you.
Customer service hours of operation:
Monday-Friday: 8:00am – 4:30pm CST.
Holiday weekends:
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.
Visit us on the web at www.santasbest.com
PRE-LIT & PRE-SHAPED CHRISTMAS TREE
A
B
C
Foot Pedal
Fig 5
Fig 1
FLOCKING OR GLITTER DISCLAIMER
Notice: Your pre-lit tree has been professionally flocked or
glittered.
Upon the tree sections being removed from its carton, you will
notice an accumulation of flocking or glitter at the base of the carton.
Do not be alarmed.
This loose flocking or glitter material was accounted for and
planned in the packing and manufacturing process of this tree.
In no way has the appearance or the integrity of the tree's
quality been compromised.
During future Holiday seasons you can expect a light dusting of
flocking or glitter to loosen from your tree during the packing and
unpacking process. Extra flocking or glitter has been adhered to
your tree to account for this minor annual loss.
The overall beauty of your tree will not be diminished.
Simply sweep or vacuum up the loose flocking or glitter upon the
assembly completion. During the flocking or glitter process the
light bulbs themselves have been flocked or glittered. This was
purposely done for the overall lighting effect of the tree.
PLEASE NOTE: Your flocked tree must NOT be stored in a plastic
bag or bags as moisture and condensation may occur, causing for
the discoloration of the flocking material.
Your flocked or glittered tree must be stored in a cool and dry location
protected from excessive exposure to moisture, heat or sunlight.
With proper care and proper storage location, you will experience
many years of enjoyment.
18”
2017 Home Depot
Natural Balsam/Majestic Fir RGB with Flocked Tree Instruction Sheet - 102 Function Remote (English)
Date: 5/4/17
17”
Items # 3270109F-ILPHO (6.5ft Flocked Balsam)
3270110F-ILPHO (7.5ft Flocked Balsam)
3270111F-ILPHO (9ft Flocked Balsam)
RW75146-IPHO (7.5ft Majestic Fir)