User manual
LED Wall Light, 3x1W
Version 11/09
Item-No. 57 55 74 °
Intended Use
The LED light is intended for wall installation and for use in indoor and outdoor (protection
type IP54) areas e.g. entrance areas, terraces, etc, where it provides energy-efficient fash-
ion lighting.
Any other use than as described above can damage the product. Moreover, this may give rise
to hazards such as short-circuiting, fire, electric shock, etc. No part of the product may be mod-
ified or rebuilt!
The safety instructions must be observed at all times!
This product complies with the applicable National and European requirements.
All names of companies and products are the trademarks of the respective owner. All rights
reserved.
Package Contents
• LED light
• Mounting material (screws/wall plugs)
• Operating Instructions
Symbols, Superscripts
Ꮨ
This symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specific risks associated with handling, function
and use.
☞
The „Hand“ symbol indicates special tips and operating information.
The device is suitable for direct mounting on normally inflammable surfaces
Defective safety glass must be replaced immediately; if the safety glass
is defective the product must not be operated.
IP54 Protection type IP54 (splash proof ), the product is suitable for use in outdoor-
areas
Safety Instructions
Read the complete operating manual carefully before using the product as it
contains important information about the correct installation and operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases!
Caution!
The product may only be installed by a qualified technician (e.g. electrician)
who is familiar with the relevant regulations (e.g. VDE, German electrical
wiring regulations)!
Improper work carried out at the mains voltage endangers not only your life
but also the life of others!
If you do not have the expertise required for the installation, do not install it
yourself but entrust a qualified electrician.
• The unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children! There is
the risk of a fatal electric shock!
• The product may only be operated on the mains voltage (see section „Technical
Data“). Never try to operate the product at another voltage as this will cause its
destruction.
Ꮨ
OPERATING INSTRUCTIONS www.conrad.com
• The product is designed to protection class I, the protective earth wire must be-
connected.
If there is not a mains supply with a protective earth wire available at the place of
installation, the product must not be connected/used there. In this case, lay a new
supply with a protective earth wire.
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• Do not use the product in rooms or in poor ambientconditions where flammable
gases, vapours or explosive dust may be present or are present!
• The product is splash-proof (IP54).
• Attention, LED light: Do not look directly into the LED light! Do not look into the
beam directly or with optical instruments! Risk for eye injuries!
• Do not use the light any longer, if the safety glass is damaged!
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• In commercial institutions, the accident prevention regulations of the employer’s
liability insurance association for electrical systems and operating facilities are to
be observed!
• If you have reason to assume that safe operation is no longer possible, discon-
nect the light immediately and secure it against inadvertent operation. It can be
assumed that safe operation is no longer possible if:
- the light shows visible signs of damage or
- the light does not work any more
Preparations for Installation
Ꮨ
Please note:
The product may only be installed by a qualified technician (e.g. electrician)
who is familiar with the relevant regulations (e.g. VDE, German electrical
wiring regulations)!
• The product may be installed and operated in both indoor and outdoor areas; the product is
intended for installation on a wall. Do not use the product in or under water, there is a danger
of a fatal electric shock!
Protect the light from salt water (e.g. de-icing salt in the winter) since it may lead to corrosion.
• Make sure you install the light on a solid base (e.g. brickwork).
• Use a suitable mains cable for the connection, which is laid and fitted into the brickwork.
• The light must be protected on the distribution board, provided by the user, by a 10/16A fuse.
An earth leakage circuit breaker must be installed before this (FI protective switch).
• The light must be voltage-free during installation. It is not sufficient to just turn off at the light
switch!
Turn the power off, and remove the electric circuit fuse or switch off at the circuit breaker.
Secure it against an unauthorised re-start, e.g. with a danger sign. Furthermore, turn off the
earth leakage circuit breaker in order to disconnect from all the poles of the mains supply.
• Check that the mains cable is free of current e.g. with an appropriate tester.
Installation/Connection
Read the information in chapter „Preparations for Installation“ prior to instal-
lation and connection!
☞
The light is designed to be used with the light pointing downwards.
If the light is mounted so that the light points upwards, water may accumulate on
the glass covering the light opening, depending on the design.
Due to the evaporation of the water caused by the increased heat, dust and dirt will
accumulate on the light cover over time, which will lead to an impairment in the light
emitted.
If you want the light to point upwards, we recommend you use an installation area
that is protected from precipitation or that you clean the light cover frequently.
• Open the light by removing the wall bracket. To do this, unscrew the grubscrews on the round
housing slightly, using a suitable hexagon spanner.
• Mark the positions to drill the holes on the wall using the openings of the wall bracket as tem-
plate.
• Depending on the subsurface, appropriate screws/wall plugs must be used when installing the
wall bracket.
Ꮨ