ENGLISH.............................................................................................2 LIGHTING INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Always wear safety goggles when operating tools.
ENGLISH TRANSFORMER SET-UP Refer to local building codes for installation requirements; failure to install this product in accordance with building codes may affect safety of the product and void product warranty. Refer to manufacturers safety instructions when operating any tools. Pre-Installation Notes: • Follow all national and local building/ electrical codes. • Transformer must be plugged into GFCI outlet. • Transformer can support up to 50 watts output. • DO NOT CUT wires.
ENGLISH 3. Mount the T-Connector. Run the 4' output power cable with the T-connector attached to the location of the first light (typically located at the base of the first post) or a central location if lights will be located in multiple directions. The T-connector can be secured loosely using (2) #4 x 1" zinc plated or stainless steel screws (not supplied). Do not tighten the screws completely as this can damage the T-connector.
ENGLISH SUPPLYING POWER TO YOUR FIRST POST Do NOT cut any wires during your installation. Wire harnesses can be purchased in lengths of 5', 7' and 9'. Excess wire can be coiled up in the posts or beneath the deck surface for a clean installation.. 1a. 1b. 1c. Using 4" x 4" Wood Posts with Sleeve: Using Steel Post Install Kit with Sleeve: Using an Aluminum Post: Cut all 4" x 4" posts to a height of 35 ½" from deck surface for a 36" high installed railing; 41 ½" for a 42" high installed railing.
ENGLISH CONNECTING WIRE HARNESSES 1. 2. 3. Wire Harnesses: 2-Way Splitter: 5-Way Splitter The harness is used to extend power from the transformer to each individual light or splitter. The harness has a male and female end (Fig. 1). The 2-Way Splitter is used to evenly distribute power from 1 input to 2 outputs. The 5-Way Splitter is used to evenly distribute power from 1 input to 5 outputs. Plug the male connector from a harness into the female input connector of the 2-Way Splitter (Fig. 3).
ENGLISH LED POST CAP INSTALLATION Crossover Product transformer, harnesses, and splitters are compatible with all Crossover Product lighted accessories (post caps, side/stair lights, dome lights, under-rail lighting, and flush-deck lights) and Transform lighted accessories (Transform post caps, Transform dome lights). 1. 2. 3. Plug the male connector that is at the top of your post (Fig. 1) into the female connector attached to the light. Press firmly until the connection is fully engaged.
LED SIDE LIGHT INSTALLATION ENGLISH Crossover Product transformer, harnesses, and splitters are compatible with all Crossover Product lighted accessories (post caps, side/stair lights, dome lights, under-rail lighting, and flush-deck lights) and Transform lighted accessories (Transform post caps, Transform dome lights). Follow instructions for wiring harness so that there is a male connector at each location that will have a light installed. 1. 2. 3.
ENGLISH LED DOME LIGHT INSTALLATION Crossover Product transformer, harnesses, and splitters are compatible with all Crossover Product lighted accessories (post caps, side/stair lights, dome lights, under-rail lighting, and flush-deck lights) and Transform lighted accessories (Transform post caps, Transform dome lights). Follow instructions for wiring harness so that there is a male connector at each location that will have a light installed. 1. 2. 3.
LED FLUSH MOUNT LIGHT INSTALLATION ENGLISH Crossover Product transformer, harnesses, and splitters are compatible with all Crossover Product lighted accessories (post caps, side/stair lights, dome lights, under-rail lighting, and flush-deck lights) and Transform lighted accessories (Transform post caps, Transform dome lights). Follow instructions for wiring harness so that there is a male connector at each location that will have a light installed. 1. 2. 3. Layout the location of the light(s).
ENGLISH LED UNDER-RAIL LIGHTING INSTALLATION Crossover Product transformer, harnesses, and splitters are compatible with all Crossover Product lighted accessories (post caps, side/stair lights, dome lights, under-rail lighting, and flush-deck lights) and Transform lighted accessories (Transform post caps, Transform dome lights).
ENGLISH 3. 4. 5. Run a harness down the inside of the post, with the male connector accessible at the top of the post (Fig. 5). Thread the female end of the under-rail light strip through the hole in the top rail and through the hole in the post, being careful not to cut or damage the light strip or wiring if threading through a metal post. Plug the male connector into the female connector attached to the under-rail light strip (Fig. 6).
Need a little help installing your railing? www.rdirail.com/support/installation-videos.html BARRETTE OUTDOOR LIVING EGG HARBOR CITY, NJ 08215 TEL: (877) 420-7245 FAX: (866) 277-5160 E-MAIL: CS@RDIRAIL.COM URL: WWW.RDIRAIL.COM REV. 02.