SDS

ManualsBrandsUnbranded ManualsOutdoor Recreation65" Venture Multi-Use Utility Sled

Material Safety Data

Sheet

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

MARLEX® and MARFLEX® Polyethylenes (All

Grades except CL, L and Masterbatch Series)

Product Use: Extrusion and Compounding, Film and Coatings, Molded Articles, Plastic Molding Compound, Resin

Product Number(s): 0001098194, 0001041625, 0001094725, 0001068160, 0001041626, 0001041627, 0001097683,

0001094724, 0001097684, 0001097685, 0001041614, 0001097686, 0001097682

Synonyms: Plastic

Product CAS No.: Mixture

Company Identification:

Chevron Phillips Chemical Company LP

10001 Six Pines Drive

The Woodlands, TX 77380

Chevron Phillips Chemicals International N.V.

Brusselsesteenweg 355

B-3090 Overijse

Belgium

Product Information:

MSDS Requests: 1 - (800) 852-5530

Technical Information: 1 - (800) 852-5531

Responsible Party: Product Safety Group

Email:msds@cpchem.com

24-Hour Emergency Telephone Numbers

HEALTH:Chevron Phillips Emergency Information Center 866.442.9628 (North America) and 1.832.813.4984

(International)

TRANSPORTATION: North America: CHEMTREC 800.424.9300 or 703.527.3887

ASIA: +1.703.527.3887

EUROPE: BIG .32.14.584545 (phone) or .32.14.583516 (telefax)

SOUTH AMERICA SOS-Cotec Inside Brazil: 0800.111.767

Outside Brazil: 55.19.3467.1600

MEDICAL APPLICATION CAUTION: Do not use this Chevron Phillips Chemical Company LP material in medical

applications involving permanent implantation in the human body or permanent contact with internal body fluids or

tissues.

Do not use this Chevron Phillips Chemical Company LP material in medical applications involving brief or temporary

______________________________________________________________________

Revision Number: 8

Revision Date: 08/07/2007

1 of 9

MARLEX® and MARFLEX®

Polyethylenes (All Grades except CL, L

and Masterbatch Series)

MSDS : 240370

Summary of content (9 pages)

PAGE 1
Material Safety Data Sheet SECTION 1 PRODUCT AND COMPANY IDENTIFICATION MARLEX® and MARFLEX® Polyethylenes (All Grades except CL, L and Masterbatch Series) Product Use: Extrusion and Compounding, Film and Coatings, Molded Articles, Plastic Molding Compound, Resin Product Number(s): 0001098194, 0001041625, 0001094725, 0001068160, 0001041626, 0001041627, 0001097683, 0001094724, 0001097684, 0001097685, 0001041614, 0001097686, 0001097682 Synonyms: Plastic Product CAS No.
PAGE 2
implantation in the human body or contact with internal body fluids or tissues unless the material has been provided directly from Chevron Phillips Chemical Company LP under an agreement which expressly acknowledges the contemplated use. Chevron Phillips Chemical Company LP makes no representation, promise, express warranty or implied warranty concerning the suitability of this material for use in implantation in the human body or in contact with internal body fluids or tissues.
PAGE 3
* This value is for inhalable (total) particulate matter containing no asbestos and < 1.0% crystalline silica. SECTION 4 FIRST AID MEASURES Eye: Flush eyes with running water immediately while holding the eyelids open. Remove contact lenses, if worn, after initial flushing, and continue flushing for at least 15 minutes. Get immediate medical attention. If heated material should splash into eyes, flush eyes immediately with fresh water for 15 minutes while holding the eyelids open.
PAGE 4
manner consistent with applicable regulations. If heated material is spilled, allow it to cool before proceeding with disposal methods. Reporting: U.S.A. regulations may require reporting spills of this material that could reach any surface waters. Report spills to local authorities and/or the National Response Center at (800) 424-8802 as appropriate or required. SECTION 7 HANDLING AND STORAGE READ AND OBSERVE ALL PRECAUTIONS ON PRODUCT LABEL .
PAGE 5
limitations supplied with the equipment since protection is usually provided for a limited time or under certain circumstances. ENGINEERING CONTROLS: Use in a well-ventilated area. If handling results in dust generation, special ventilation may be needed to ensure that dust exposure does not exceed the OSHA PEL for nuisance dust. If heated material generates vapor or fumes, use process enclosures, local exhaust ventilation, or other engineering controls to control exposure.
PAGE 6
Conditions to Avoid: Not Applicable Incompatibility With Other Materials: May react with oxygen and strong oxidizing agents, such as chlorates, nitrates, peroxides, etc. Hazardous Decomposition Products: Low molecular weight hydrocarbons, alcohols, aldehydes, acids and ketones can be formed during thermal processing. Hazardous Polymerization: Hazardous polymerization will not occur.
PAGE 7
SECTION 14 TRANSPORT INFORMATION The description shown may not apply to all shipping situations. Consult appropriate Dangerous Goods Regulations, for additional description requirements (e.g., technical name) and mode-specific or quantity-specific shipping requirements. Shipping Descriptions per regulatory authority.
PAGE 8
The following components of this material are found on the regulatory lists indicated. Polyethylene 4 WHMIS CLASSIFICATION: This product is not considered a controlled product according to the criteria of the Canadian Controlled Products Regulations. CHEMICAL INVENTORY LISTINGS: AUSTRALIA: This material contains components that require notification before sale or importation into Australia.
PAGE 9
EC50 LD50 NDA <= CNS - Reauthorization Act. Effective Concentration Lethal Dose No Data Available Less Than or Equal To Central Nervous System LC50 CAS NA >= MAK - Lethal Concentration Chemical Abstract Service Not Applicable Greater Than or Equal To Germany Maximum Concentration Values This data sheet is prepared according to the latest adaptation of the EEC Guideline 67/548. This data sheet is prepared according to the OSHA Hazard Communication Standard (29 CFR 1910.1200).