SPECIFICATIONS (規格書) 編 號 NO. DOCUMENTCONTROLLED 29 MAY 2008 公 司 名 稱 CO. Name : F-JM10K-01-068 CONRAO : 型 號 名 稱 Model Name : F-JM10K B10K-4(60 度 中 6 度 SLIVER) 一 、 ELECTRICAL CHARACTERISTICS 電 氣 特 性 序號 NO.
The rated power should be changed according to the following chart when the ambient temperature changed. 它與環境溫度按以下曲線變化。 Derating curve of rated dissipation 4 5 Rated power 額定功率 Contact Noise 接觸雜音 (CRV) Page 2 of 7 Linear Taper B: 0.0125W B 型: 0.
6 Voltage Divider Error 分壓誤差值 Voltage divider error is defined the ratio of the voltage terminals 1-2 to terminals 1-3 after the drive arm rested. 5V D.C. shall be applied to the terminals between 1and 3 and then voltage divider error shall be measured with the drive arm operation on the line X-X and Y-Y. (Terminal 1-2/Terminal 1-3 × 100%) 分壓誤差值是搖杆自由復歸后端子 1-2 與端 子 1-3 電壓比例.將 5V D.C 電壓加在端子 1-3 之間, 分壓誤差值在搖杆運作於 X-X 和 Y-Y 方向到底復歸后測試.(端子 1-2/端子 1-3 ×100%) 39.6% ~ 60.
8 Insulation resistance 絕緣阻抗值 More than 100 MΩ 100 MΩ以上 Apply 250VDC to the individual terminals and case. 金屬外殼與端子間加 DC250V 電壓 9 Withstand voltage 耐電壓特性 Without arcing or breakdown 無損壞或弧光 Apply one minute of 250VAC to the individual terminals and case. 在特定端子與外殼間加 AC250V 電壓 1 分鐘. 二 、 MECHANICAL CHARACTERISTICS 機 構 特 性 序號 NO.
7 Operation angle of lever 搖杆使用有效 角度 Refer to attached product drawing 見成品圖 The maximum angle of the lever pushed to the direction of X-X and Y-Y and 45°. 搖杆推向 X-X(Y-Y)和 45°方向的最大角 度. 三 . ENDURANCE CHARACTERISTICS 耐 久 性 能 (Single test of item 單 一 測 試 項 目 ) 序號 項 NO. ITEM PERFORMANCE Free falling 自由落下試驗 No damage and lever deformation, but deformations of terminals and molded parts are allowed. 無不良產生,端子變形除外. 1 目 性 能 Variation of total resistance +5% should be within–30%.
5 Temperature cycling test 溫度循環測試 The total resistance change should be within ±20%. To be operated mechanically. 全阻值變化要在±20%以內, 機械方面能動作。 Low temperature : -10 ±3℃ 30 minutes High temperature: +60 ±2℃ 30 minutes Number of cycles: 5 Surface moisture shall be removed, and then the controller shall be subjected to standard atmospheric conditions for 2 hours after which measurement shall be made. 在低溫為-10 ±3℃放置 30 分鐘,高溫 60 ± 2℃放置 30 分鐘,測試 5 次.表面水份攝取 后 2 小時后正常狀態下測試.
2 Travel 移動量 3 Push strength 按壓強度 4 Circuit diagram 電路圖 0.5-0.4mm Put the switch lever upward, apply 2 times of the static operating force over the lever’s axial direction of the lever, measure the variance of the switch stroke. 將開關操作部(搖杆)置於靜止位置,並在操 作柄中央施加兩倍於作動力之靜負荷測 量柄被壓到不動時之移動距離. No mechanical and electrical malfunction. 不得有電氣及機構上之異常現象. Put the switch lever upward; apply 3kgf of the static load over the vertical direction of the lever for 60 seconds. 將開關之操作部(搖杆)置於垂直方向,並沿 操作方向加 3kgf 之靜負荷 60 秒.
序號 項 目 NO. ITEM Unless otherwise specified, test and measurement should be carried out in following condition: 如無特殊要求,試驗與測試將按以下條件進行: Ambient temperature 溫度 15°C to 35°C Relative humidity 相對濕度 25% to 75% Air pressure 氣壓 86 KPa to 106 KPa 2 Operating temperature range 使用溫度範圍 -10°C to +70°C 3 Storage temperature range 儲存溫度範圍 -30°C to +80°C 1 Approved 核 准 Q.I.Department 審 查 Design dept. 經 辦 者 倪艷麗 Page 8 of 7 QR-QE-20/2003.08.
DOCUMENT CONTROLLED 29 MAY 2008 普耀集團有限公司