OWNER’S MANUAL ™ Gourmet Series Marine Gas Grill Model A10-918-2 For questions regarding performance, assembly, operation, parts, or returns, contact the experts at MAGMA by calling (562) 627-0500 7:00 a.m. - 5:00 p.m. Pacific Time Monday thru Friday or e-mail us at mail@MagmaProducts.com IMPORTANT, read these instructions carefully before use. Familiarize yourself with the appliance before connecting it to its gas container. Keep these instructions for future reference.
IMPORTANT SAFETY WARNINGS READ ALL INSTRUCTIONS BEFORE OPERATING. s 53% /54$//23 /.,9 s $/ ./4 53% 4()3 !00,)!.#% ).3)$% 4(% "/!4 /2 !.9 %.#,/3%$ 30!#% s '2),,3 2!$)!4% (%!4 #,%!2!.#% &2/- #/-"534)",%3 v 3)$%3 !.$ "!#+ .%6%2 53% 5.$%2 !7.).'3 0!4)/ #/6%23 %4# s 53% 02/0!.% '!3 /.,9 &5%, 34/2!'% 3(/5,$ "% ). #/-0,)!.#% 7)4( 4(% !-%2)#!. "/!4 !.$ 9!#(4 #/5.#), !"9# 34!.$!2$3 ! -!2).% ,)15)&)%$ 0%42/,%5- '!3 ,0' 3934%-3 s &/2 .!452!, '!3 !00,)#!4)/. #/.
MOUNT HARDWARE Fasteners are supplied for both Single Mount and Dual Mount grill mounting options. See Magma Catalog or Website for best mount selection. Single mount through-bolt applications 4 Carriage bolts & lock nuts. Single mount non-through-bolt applications, including Style 1 “Levelock” 4 Hex head bolts & lock washers. Dual mount applications 4 Carriage bolts & lock nuts. Only 4 bolts required for grill mounting. Place bolts (2 per side) diagonally from each other as shown.
OPERATING PROCEDURES OPERATE ONLY ON “LOW” WHEN LID IS CLOSED. ALWAYS OPERATE WITH GREASE TRAY IN PLACE. WARNING: Do not overheat grill. Magma Grills do not require pre-heating. Stainless Steel loses anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low temperature with the lid closed. If medium or high heat is required, grill with lid open. LIGHTING INSTRUCTIONS s s s s s /PEN LID DURING LIGHTING $EPRESS KNOB AND ROTATE COUNTER CLOCKWISE TO THE h()'(v flame position.
ELECTRODE SPARK ADJUSTMENT CAUTION: Spark can cause small shock. Do not leave fingers on or near electrode wire while engaging igniter. A s %LECTRODE WIRE SHOULD BE approximately 1/8” from gas EXIT HOLE IN BURNER. Carefully adjust wire if required. DISASSEMBLY & RE-ASSEMBLY s ,IFT RADIANT PLATE UP OUT OF LEFT SLOT SEE " AND REMOVE BY SLIDING IT OUT OF right slot (see C). s 2EMOVE BURNER RETAINER PIN SEE " REMOVE BURNER )NSPECT BURNER REMOVE ANY OBSTRUCTIONS #!54)/. 7(%. 2%0,!#).' "52.
MAINTENANCE Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture. It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry.
)-0/24!.4 s $/ ./4 #/..%#4 ! ()'( 02%3352% 3500,9 (/3% FROM A NON-REGULATED TANK DIRECTLY TO GRILL. Magma's grills are designed for use with small disposable propane canisters or with pre-regulated low-pressure propane and optional low-pressure valves. Running high-pressure propane fuel supply lines on a boat is in violation of American Boat & Yacht Council (ABYC) guidelines and is not considered a safe application.
CONTENTS A B x4 x4 C x4 x4 A) (1) 3/16” Hex key wrench for lid removel. B) Pack of (4) 1/4”-20 x 5/8” hex head screws and internal lock washers for Single Mount non-through-bolt applications, including Style 1 “LeveLock”. C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and lock nuts for dual mount and single mount applications. LIMITED WARRANTY Magma Products, Inc. guarantees this product to be free from defects in materials or workmanship to the original consumer.