Installation Guide

ManualsBrandsUnbranded ManualsCommercial LightingNICOR 4 ft. 4-Light 4000K White Equivalent LED Wrap Around Light Fixture with Prismatic Lens

CAUTION: For your safety and proper operation of this fixture, read instructions

carefully before you start. Note and understand all safety information in bold print.

1) WARNING: RISK OF SHOCK

House electric current can cause painful shock or serious injury unless handled properly.

For your safety, always remember to:

-Turn off the power supply at the fuse or circuit breaker box before you install the fixture.

-Turn off the power supply again when you change lamps or perform other maintenance.

-Ground the fixture to avoid potential electric shocks and to ensure reliable starting.

-Double check all connections to be sure they are all tight and correct.

-Wear rubber-soled shoes and work on a sturdy wooden ladder.

Couper le courant au niveau du disjoncteur avant d’installer la lampe pour éviter tout risque de

secousse électrique.

2) This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also

designed to be installed in accordance with local electrical codes. If you are unsure about the

wiring, consult a qualified electrician and check your local electircal code.

Tous les branchements électrique doivent respecter les normes du Code National de l’Électricité.

Si vous ne savez pas comment installer correctement des fils électriques,appelez un électricien

professionnel.

3) WARNING: RISK OF CUTS

Some metal parts in the fixture may have sharp edges. To prevent possible cuts and scrapes,

we suggest gloves to be worn when handling all parts from this fixture.

4) Account for small parts and destroy packing material, as these may be hazardous to children.

5) WARNING: RISK OF FIRE

Most dwellings built before 1985 have supply wire rated 60°C.

wire must be suitable for at least 90C ( 194 ˚F ). Consult a qualified electrician before installing.

LES FILS D’ALIMENTATION 90°C MIN.

A) LAMP HOUSING 1 UNIT C) WIREWAY COVER 1 UNIT A) PLIERS C) PHILPS SCREWDRIVER

B) LENS 1 UNIT D) WOOD SCREWS 4 UNITS B) HAMMER D) SAFETY CLASSES

E) WIRENUTS 3 UNITS

WARNING: Before wiring to the power supply, turn off the electricity at fuse or circuit

breaker box. Ensure grounding to avoid potential electrical shock and to ensure

reliable lamp starting.

1) Remove the Acrylic lens from the fixture and place aside on a flat surface to avoid damage

INSTALLATION INSTRUCTIONS

WRAP AROUND LIGHT FIXTURE

IMPORTANT SAFETY INFORMATION

FOR YOUR PROTECTION, READ CAREFULLY

INSTALLATION INSTRUCTIONS

PREPARATION OF LIGHT FIXTURE FOR INSTALLATION

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CAUTION: For your safety and proper operation of this fixture, read instructions carefully before you start. Note and understand all safety information in bold print. WRAP AROUND LIGHT FIXTURE IMPORTANT SAFETY INFORMATION FOR YOUR PROTECTION, READ CAREFULLY 1) WARNING: RISK OF SHOCK House electric current can cause painful shock or serious injury unless handled properly.
PAGE 2
to the lens. To remove the lens, carefully slide the lens to one end of the fixture. Gently grab the lens and pull it out. 2) Squeeze wireway cover at both ends on both sides to release from the fixture housing. Remove the cover and place aside on a flat surface for later use. 3) Carefully turn the fixture housing over and locate the center knockout on the housing.
PAGE 3
Diagram 2 Diagram 3 3) Drill 1/8" pilot hole at each location. 4) If drill encounters ceiling joist, use wood screws ( provided ) & washers ( not included ) to secure fixture housing to the ceiling. See diagram 4. 5) If drill DOES NOT ENCOUNTER CEILING JOIST, use 4 toggle bolts and washers ( both not included ). Enlarge the pilot drill hole size large enough to accommodate the toggle bolts tighten and secure fixture housing to ceiling. See Diagram 5.
PAGE 4
Diagram 6 INSTALLATION INSTRUCTIONS WARNING: Before wiring to the power supply, turn off the electricity at fuse or circuit breaker box. Ensure grounding to avoid potential electrical shock and to ensure reliable lamp starting. WIRING OF THE LIGHT FIXTURE 1) Connect the black supply ( house ) wire to the black wire from the light fixture. Secure the connection by inserting into the wirenut, then revolving until secure.Diagram 1.