Operator's Manual CAGE™ PERMANENT HUB BLIND R30 MODEL CBR30T Get parts online at www.HuntRiversEdge.
Operator's Manual CAGE™ R30 INTRODUCTION If for any reason you have a problem with your product or are missing any parts, DO NOT return to the retailer, contact Rivers Edge® Customer Service Department at 800-345-6007 for assistance. CONTENTS Introduction/Warranty...................................................................................................................................................................................................................2 Warnings........................
Operator's Manual CAGE™ R30 STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY WARNING This tent is made with fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any flame source. Heat sources burn oxygen and emit carbon monoxide. Use caution with heaters and vent properly. • Do not use candles, matches or open flames of any kind in or near a tent. • Do not cook inside a tent.
Operator's Manual CAGE™ R30 SERVICE PARTS LIST (NOT TO SCALE) Item Part No. Description 1 # 38396 ROOF HUB ASSEMBLY 1 2 # 37034 ROOF LOCK 1 3 # 37113 WALL HUB ASSEMBLY 4 4 # 38395 BOTTOM CORNER HUB ASSEMBLY 4 5 # 38390 TOP CORNER HUB ASSEMBLY 4 4 Image Qty Check for parts online at www.HuntRiversEdge.
Operator's Manual CAGE™ R30 SERVICE PARTS LIST (NOT TO SCALE) Item Part No.
Operator's Manual CAGE™ R30 STEP 1 & 2 SET-UP INSTRUCTIONS WALL 1. Remove the blind from carry bag. 2. Lay the blind flat on the ground so any wall panel is facing upward. Be completely sure there is no material twisted or overlapping the ends of any poles. SEE FIGURE 1. FIGURE 1 3. NOTE: Walls are meant to be strong/ridged and will require a fair amount of force to pop over center for set up 4. FIGURE 2 Repeat step 3 for the remaining walls so the blind is standing up. SEE FIGURE 3.
Operator's Manual CAGE™ R30 5. Unzip the door and enter the blind. Place palm of your hand on the roof hub and push the spring loaded roof straight up until it pops over center. SEE FIGURE 4. STEP 5 NOTE: For easier set up, it’s best to open up some window panels to allow light into blind for better visibility. NOTE: The roof hub is under spring tension; use extreme caution when popping roof up and collapsing roof down to avoid injury to face, head or hands.
Operator's Manual CAGE™ R30 STEP 7 - 9 UNLOCKED CLAMP 7. Unpack the horizontal and vertical spreader poles from the pole bag. 8. Starting with the (4) horizontal spreader poles with the disc shaped ends, place one end into slot on any top corner hub. Make sure clamp is in the unlocked position. SEE FIGURE 6A & 6B. FIGURE 6A Insert opposite end of spreader pole into slot of top corner hub located across the same side of blind.
Operator's Manual CAGE™ R30 STEP 11 INSERT PEG FIGURE 8A 11. Install (4) vertical spreader poles with the round peg ends. With clamp on the vertical pole in the unlocked position, place peg into hole on bottom corner hub. SEE FIGURE 8A & 8B. NOTE: The larger diameter pole should go towards the bottom corner. FIGURE 8B FIGURE 9A 13. While keeping vertical poles spread apart, flip clamp lever on the vertical pole into the locked position. STEP 12 - 14 12.
Operator's Manual CAGE™ R30 STEP 15 UNLOCKED CLAMP 15. Go back to the (4) horizontal spreader poles; while spreading them outward (tight), flip clamp lever into the locked position. SEE FIGURE 9A & FIGURE 9B. FIGURE 9A NOTE: Once all of the poles are clamped locked return to the roof lock and give it one final twist to ensure it is tight. LOCKED CLAMP FIGURE 9B STEP 16 16. Remove the ground stakes from bag. Pull each corner outward (taut).
Operator's Manual STEP 17 - 21 CAGE™ R30 FIGURE 11 17. Anchor the side walls by attaching the short part of the strap to eye bolt. SEE FIGURE 11. 18. Attach the long strap to spiral anchor. SEE FIGURE 12. FIGURE 12 FIGURE 13 20. Feed end of long strap through cam lever on short strap on eye bolt. Pull tight. SEE FIGURE 13. STEP 19 - 21 19. Measure the distance from side wall eye bolt to approximate location of spiral anchor, and twist anchor into ground. 21. Repeat steps 17-20 for remaining sides.
Operator's Manual CAGE™ R30 TAKE-DOWN INSTRUCTIONS STEP 1 - 6 TURN COUNTERCLOCKWISE FIGURE 14A - LOCKED POSITION 1. Remove all ground stakes and store them in the provided bag. 2. Remove all native brush from brush holder straps. 3. Unscrew the roof lock fully by rotating counter-clockwise until it hits nut on bottom of bolt. SEE FIGURE 14A & 14B. 4. Unlock all vertical and horizontal spreader poles and remove. Horizontal poles may need a twist to remove from slots. 5.
Operator's Manual STEP 8 - 11 CAGE™ R30 8. Zip door closed. 9. From outside of blind push in each wall allowing them to fold onto themselves. SEE FIGURE 16. 10. Blind will be back in its flat stage just as it was when it was unfolded out of the backpack bag. Gather all corners of the blind and fold together. Do not force the blind when folding. Watch for entanglement of poles. Use the long packing strap to wrap around blind and tighten. 11.
Operator's Manual CAGE™ R30 ILLUSTRATED PARTS BREAKDOWN 1 2 9 7 5 3 8 6 4 14 Check for parts online at www.HuntRiversEdge.
Operator's Manual CAGE™ R30 PARTS LIST Item Part No. Description Qty 1 # 38396 ROOF HUB ASSEMBLY 1 2 # 37034 ROOF LOCK 1 3 # 37113 WALL HUB ASSEMBLY 4 4 # 38395 BOTTOM CORNER HUB ASSEMBLY 4 5 # 38390 TOP CORNER HUB ASSEMBLY 4 6 # 36283 FIBERGLASS POLE ASSEMBLY 16 7 # 35791 HORIZONTAL SPREADER POLE ASSEMBLY 4 8 # 35795 VERTICAL SPREADER POLE ASSEMBLY 4 9 # 35806 ROOF POLE ASSEMBLY CBR30BT 4 PARTS NOT SHOWN Item Part No.
Rivers Edge® Treestands, A Division of Ardisam, Inc. 1160 Eighth Avenue, PO Box 755 Cumberland, WI 54829 Phone: 800-345-6007 Fax: 715-822-2124 www.huntriversedge.com *All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.
