Instructions / Assembly

ManualsBrandsUnbranded ManualsAir Filters & AccessoriesAirPro Parts 24-Volt Germicidal UV Light for HVAC Systems

GERMICIDAL

UV SYSTEM

This manual covers the following model:

All Pro Parts UV #19310

Installation & Operation Manual

INCLUDED INSIDE BOX

• Power Module

• Germicidal UV lamp

• Power cord

• Remote lamp cord

• Magnetic Mounting bracket

• Filter shield

• Self-drilling screws

• UV safety viewport

• UV safety label

• Installation & operation manual

• Installation hardware

GENERAL

This product emits germicidal ultraviolet

(UV-C) light to help disinfect the cooling

coil, drain pan, and internal surfaces of

HVAC systems for improved indoor air

quality.

BEFORE INSTALLING

• Read all instructions carefully. Failure

to do so could damage the equipment

or cause harm to yourself or others.

• Acknowledge all warnings.

• Only qualified technicians should per-

form the installation.

Summary of content (9 pages)

PAGE 1
GERMICIDAL UV SYSTEM Installation & Operation Manual This manual covers the following model: All Pro Parts UV #19310 GENERAL INCLUDED INSIDE BOX This product emits germicidal ultraviolet (UV-C) light to help disinfect the cooling coil, drain pan, and internal surfaces of HVAC systems for improved indoor air quality. • • • • • • • • • • • BEFORE INSTALLING • Read all instructions carefully. Failure to do so could damage the equipment or cause harm to yourself or others. • Acknowledge all warnings.
PAGE 2
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL SPECIFICATIONS 3.35” 5.3” 1.75” 3.16” 4.75” Dimensions: Power Module: 5”L x 3.25”W x 2”H Bracket: 3.5”L x 2.25”W x 3.5”H Electrical: 24V (Expanded range ballast: 20V-32V), 50/60Hz, 1.4A. 3000V surge protection. 3-ft power cord. 4-ft lamp cord Lamp Length: 15” Weight: 2lb Humidity: Water resistant lamp. Lamp Life: 18,000-hour. Ozone free. Warranty: 5-year on power module. 2-year on lamp. U.S. Patent Nos.
PAGE 3
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL UV INSTALLATION NOTES This device is meant only to be installed in the duct portion of the HVAC system. If the UV device is installed on the inlet side (return air side) of a coil, make sure that the HVAC system is configured such that the blower is located between the return air filter and the in-let of the coil, such as would be found in a traditional up-flow, or horizontal furnace with the coil placed after the heat exchanger.
PAGE 4
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL W-COIL / ABOVE A-COIL INSTALLATION (Remote Lamp) • Disconnect power to the air handler and open access panels. • Magnetic Bracket Installation - Slit insulation on the back or side wall of air handler and attach magnetic bracket to the wall. • Standard Bracket Installation - Install the lamp bracket at the desired location with two self-drilling screws (included). • Secure the lamp to the lamp bracket with the provided knurled nuts. Fig.
PAGE 5
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL A-COIL DELTA PLATE INSTALLATION (Direct Connect™) • Drill a 7/8” hole in the outer sheet metal where the lamp will be centered on the return side of the coil. See diagram. • Place gasket (included) around hole. • Insert lamp into power module and secure with self-drilling screws. (Included.) • Insert lamp/power module assembly directly into hole and secure with selfdrilling screws (Included.
PAGE 6
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL INSTALL POWER MODULE (Remote Lamp) • With the lamp cordage facing away from the mounting surface, use the long mounting screws and install the power module in a suitable location inside the control panel of the air handler using two self-drilling screws (included). Note: Do not overtighten screws. • Connect the power module to constant 24V power. • Connect input 24V power cord. Align markers on power module with power cord connector. Fig.
PAGE 7
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL 24V INSTALLATION NOTES Installing the 24V UV fixture may require an upgrade to the 24V transformer in the furnace, or air handler, depending upon the capacity of the OE specified by the manufacturer of the AHU / furnace. 1. Verify the available volt amps prior to connecting the UV fixture to the 24V circuit. Energize all 24V components so they reach their maximum amp load (Straight cool system - activate cooling.
PAGE 8
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL INSTALL UV SAFETY VIEWPORT • Adhere the provided UV safety label to the outside of the duct near the installation location and drill a 5/8” hole as indicated on the label. Press the UV safety viewport into hole. • Close all access panels and reconnect power to the air handler. • Verify that a blue glow can be seen through the UV safety viewport. NOTICE Replace Lamp Per Recommended Maintenace Schedule.
PAGE 9
ALL PRO PARTS GERMICIDAL UV SYSTEM INSTALLATION & OPERATION MANUAL WARRANTY ALL PRO PARTS GERMICIDAL UV SYSTEM LIMITED WARRANTY All Pro Parts warrants this UV-C Light to be free from defects in materials and workmanship under normal use and service, for a period of five (5) years from the date of purchase. This warranty does not cover UV-C lamp(s), which carry a two(2) year warranty from the date of installation.