Instructions / Assembly

Pre-Lit Hinged Trees with Low Voltage LEDs
3
Hook-On Trees
THIS TREE IS FOR INDOOR USE ONLY
Retain carton for storage purposes.
Each carton contains one top section, one center pole with
color-coded branch brackets (larger trees include additional
poles), one tree stand and color-coded branches.
1. Unfold tree stand and insert eye bolts. Remove packing
material from ends of poles. Insert center pole(s)
securely into stand.
2. BRANCH SHAPING. (Branches should be attached to
tree pole from the bottom up.) Locate the color-coded
branches that match the color code of the bottom bracket
on the center pole (Figure 1). Each branch must be
shaped to a natural position by spreading out the left
and right tips away from the center tip (Figure 2). See
Shaping Instructions on page 7.
3. After all bottom bracket branches are properly shaped
they can be attached to the center pole brackets. Gently
push each branch down into the bracket slots until they
lock into place (Figure 3).
4. Continue to work your way up the pole shaping and
attaching branches as described above.
5. When all tree branches have been attached, the tree
top section can be shaped and attached. Shape the tree
top as you did the lower branches.
6. Push bottom of tree top into green plastic “pole cap” at
top of center pole until it is firmly seated (Figure 4).
Assembly is now complete.
7. You may wish to further shape your finished tree as
desired.
STORAGE
Remove all holiday decorations. Lift tree top from pole.
Remove each branch from center pole brackets by lifting
up and out. Gently press tips back into center branch. All
tree parts can be replaced in carton and should be stored
in a cool, dry place.
Fig. 4
Fig. 3
Fig. 2
Fig. 1
IMPORTANT NOTE: When lowering
branches be extremely careful not to
tangle wire in gap between branch
and bracket.
Fig. 1
Fig. 3
MALE
CONNECTOR
FEMALE
CONNECTOR
T
RANSFORMER
WIRE
TRANSFORMER
Fig. 2
THIS TREE IS FOR INDOOR USE ONLY
Each carton contains one top section, one bottom
section (larger trees include one or more middle
sections) and a tree stand.
1. Unfold the tree stand and insert the eye bolts.
Remove packing material from ends of poles. Put
bottom section pole into tree stand making sure it is
seated properly (Figure 1). Tighten eye bolts until
bottom section is held securely.
2. Insert the middle section of the tree into the bottom
section. (If your tree has more than one middle
section, please refer to SPECIAL NOTE ABOUT
GIANT TREES on page 3.) Make sure that the light
cord(s) hang straight down with no loose slack that
could interfere with branch hinges.
3. Insert the tree top into the plastic pole cap of the
middle section center pole.
4. The male connectors of the light string cords from
the top, center and bottom sections will all connect
to the female connectors of the transformer wire
(Figure 2). Note that the male and female
connectors are keyed and will only connect in one
direction. After connection, twist closed each
connector nut securely.
GIANT TREES that include additional sections will
also have additional light string cord connections.
5. Working your way up from the bottom, gently lower
all branches from their upright setting (Figure 3). See
Important Note. Each branch must be shaped to a
natural position by spreading out the left and right
tips away from the center tip (See Shaping
Instructions, page 7). For best results, shape your
tree while lit. Continue to lower branches on upper
section(s) in the same manner. Shape as desired
making sure not to place undue pressure on the
hinge brackets.
STORAGE
Remove all holiday decorations. Gently press tips back
into center branch. Raise all branches to original upright
position taking care not to place undue pressure on the
attached ends of the branches. When disassembling
tree, a twisting motion will help to separate the sections
from each other. All tree parts can be replaced in
carton and should be stored in a cool, dry place.
6