Installation Guide

ManualsBrandsUnbranded ManualsCommercial Lighting2 x 2 Flat Panel 5000K 120-Watt Equivalent White Edge-Lit Integrated LED Troffer

PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS LISTED BELOW PRIOR TO PROPER INSTALLATION

WARNINGS CAUTIONS

• Risk of fire / electrical shock .

• LED Panel installation requires knowledge of luminaire electrical

systems.

• Risk of electric shock – disconnect power at source before installation.

• Do not make or alter any open holes in an enclosure of wiring or

electrical components during installation.

• If lamp or luminaire exhibits abnormal operation (buzzing, flickering,

minimal light, etc.), turn off power, remove luminaire and contact us.

For more information please visit www.eurilighting.com or call our

toll-free number 1-888-743-5766.

• Do not look directly at the operating LED Panel.

• Do not touch this product with wet hands.

• Do not disassemble, repair or alter lamp.

• Designed for indoor applications only.

• Suitable for damp locations.

• The luminaires should be grounded.

• This device is not intended for use with emergency exits or

emergency lights.

• Please make sure the driver supply wiring is of adequate length and

rating. Avoid any tension.

• Observe proper polarity when connecting power to driver. Unit must be

grounded as per code. L = Input Line or Hot, W = Neutral

• All connections should be according to NEC or any applicable local

code.

• Wear gloves and safety glasses every time when working with the

luminaire for installing, servicing or performing maintenance.

INSTALLATION INSTRUCTIONS - Wiring the Driver

STEP 1:

Open the cover of junction box with phillips screwdriver.

STEP 2:

Remove round knock-out and connect conduit to wiring box with proper

connectors: press the binding post with at screwdriver, insert the wire and secure.

For AC input, connect neutral wire(White) to AC-N, Live wire(Black) to AC-L and

Ground wire(Green) to the ground screw - . For 0-10V dimmer wiring:connect

the dimmer+wire to the DIM+, connect the dimmer- wire to the DIM-.

STEP 1:

Open the cover of junction box with phillips screwdriver.

Not Used

CONTINUES ON REVERSE

For customer service please call us at 1-888-743-5766

Ofce Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday

Questions?



LED Panel Series | 2x4 Class

2 ft. x 4 ft. All in One Retrot Kit

LED

Panel

2 ft. x 4 ft.

ground screw

INSTALLATION GUIDE

MODEL #: EPN24-1040s-2 / EPN24-1050s-2

Summary of content (2 pages)

PAGE 1
INSTALLATION GUIDE MODEL #: EPN24-1040s-2 / EPN24-1050s-2  LED Panel Series | 2x4 Class 2 ft. x 4 ft. All in One Retrofit Kit LED Panel Questions? For customer service please call us at 1-888-743-5766 Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday 2 ft. x 4 ft. PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS LISTED BELOW PRIOR TO PROPER INSTALLATION WARNINGS CAUTIONS • Risk of fire / electrical shock . • LED Panel installation requires knowledge of luminaire electrical systems.
PAGE 2
INSTALLATION GUIDE MODEL #: EPN24-1040s-2 / EPN24-1050s-2  LED Panel Series | 2x4 Class 2 ft. x 4 ft. All in One Retrofit Kit LED Panel Questions? For customer service please call us at 1-888-743-5766 Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday 2 ft. x 4 ft. RECESSED INSTALLATION FOR DROP-DOWN CEILINGS STEP 1: Move away ceiling tile. STEP 2: Connect power supply. STEP 3: Put the panel light into framework. STEP 4: Finish the installation.