Manual

ManualsBrandsUnbranded ManualsControllersEVOLUTION® Series Controller

EVOLUTION

Series Add-On:

EVO-HH Handheld Remote

EVOLUTION

Series Add-On:

EVO-HH Handheld Remote

Introduction

Congratulations on purchasing Toro’s new EVOLUTION Series Controller with the EVO-HH

Handheld Remote Add-On. With the Handheld Remote Add-On, you will quickly realize

savings in both time and money while keeping your landscape healthy and beautiful.

e EVO-HH system is designed exclusively for your Toro EVOLUTION Series Controller

to allow the user to remotely control watering and auxiliary zones. e user can walk the site,

testing, troubleshooting, and/or providing supplemental watering without walking back to the

controller every time.

To familiarize yourself with EVO-HH handheld system, please take a few moments to read

through this guide in its entirety.

Specifications

Handheld Remote

• Dimensions:

2.75” (7 cm) W x 7” (17,8 cm) H (over 2” antenna) x 1.25” (3,2 cm) D

(including mounting clip)

• 9V Alkaline battery (not included)

• RF reception range: 1000’ (152 m) LOS (line of sight)

• Operating temperature range: 14° – 140° F ( -10°– 60°C)

Enter

Setup PWR (Hold)

Mode

Cancel

LISTED

FCC-ID: OF7CLR1

IC: 3575A-CLR1

Summary of content (8 pages)

PAGE 1
EVOLUTION® Series Add-On: EVO-HH Handheld Remote Introduction Congratulations on purchasing Toro’s new EVOLUTION Series Controller with the EVO-HH Handheld Remote Add-On. With the Handheld Remote Add-On, you will quickly realize savings in both time and money while keeping your landscape healthy and beautiful. The EVO-HH system is designed exclusively for your Toro EVOLUTION Series Controller to allow the user to remotely control watering and auxiliary zones.
PAGE 2
Table of Contents Specifications 1 Overview 3 Installation 3 EVOLUTION® Smart Connect® 3 Installing the Remote Batteries 3 At the Controller 4 Menu Navigation 4 Adding the Device 4 At the Remote 5 Set the PIN 5 Powering the Remote 5 Set the Number of Stations 5 Start Program “A”, “B”, or “C” 5 Run an All Stations Cycle 6 Turn on a Station or Zone Manually 6 Stop All Watering 6 Change From One Running Station to Another 6 2 Remote Auxiliary Ope
PAGE 3
Installation Overview EVOLUTION® Smart Connect® Please see the install sheet that came with the Smart Connect device. LCD Screen Installing the Remote Batteries The remote receives power from a 9-volt battery (not included). To install the battery: Setup button Left arrow Up arrow Mode Setup PWR (Hold) USB Cover (future use) Down arrow Power button Right arrow Cancel Enter Enter button 1.
PAGE 4
At the Controller Menu Navigation or Use to navigate the menu commands. • To change a value, press or field, then press and • Press to move to the desired to adjust the value. ADD/REMOVE DEVICE WEATHER* ADD SOIL 1 ADD SOIL 2 ADD SOIL 3 ADD REMOTE 98 14 → • SELECT to input the desired value. Adding the Device For the EVOLUTION® Series controller and remote to successfully communicate, identical PINs must be set in both the controller and remote. 4. Press At the controller: 1.
PAGE 5
At the Remote Set the PIN 1. Press Mode PWR(Hold) to turn on the remote transmitter. 2. Press Setup twice. “SET PIN” appears on the screen. 3. Press or to set the first digit of the PIN number. Press to move to the next digit. SET PIN 98 14 Mode Setup PWR (Hold) 08 4. Repeat step 3 to set the other numbers in the 4-digit PIN. 5.
PAGE 6
Run an All Stations Cycle (ASC) Running an All Stations Cycle is useful for troubleshooting a sprinkler system. 1. Follow Step 1 above. 2. Press to move above Pto “TEST ALL”. C 3. Press to start the run time blinking. TEST ALL 03 RUN MIN TIME Mode 4. Press or to set the run time. Setup PWR (Hold) All stations will run the same length of time, in sequence, from lowest to highest possible. 5. Press Enter to start. (Leave the transmitter on during the ASC sequence.
PAGE 7
Start a Single Auxiliary Scene 1. Turn on the remote. It defaults to Manual mode. 2. Press or to select the desired Auxiliary Scene (A1 - A4). 3. Press to move to run time. MANUAL A2 05 SINGLE RUN MIN TIME Stop All Auxiliary 1. Press several times to display “AA oF” (off). 2. Press Enter to turn off all auxiliary scenes. MANUAL AA of Change from One Running Auxiliary scene 2 is set Mode 4. Adjust runtime with and Scene to Another Mode to run for 5 minutes. Setup PWR (Hold) Setup PWR (Hold) .
PAGE 8
Toro Support Toro Commitment to Quality Toro is committed to developing and producing the highest quality, best performing, most dependable products on the market. Because your satisfaction is our first priority, we have provided the Toro Helpline to assist you with any questions or problems that may arise. If for some reason you are not satisfied with your purchase or have questions, please contact us toll free at 1-877-345-8676.