Instructions / Assembly

GENERAL INFORMATION
SAFETY INFORMATION
PRE-INSTALLATION
Please read and understand this entire manual before
attempting to assemble, operate or install this product.
WARNING
• Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by
removing fuse or switching off circuit breaker.
CAUTION
• All electrical connections must be in agreement with local codes, ordinances or the National Electric
Code (NEC). Contact your municipal building department to learn about your local codes, permits and/or
inspections.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified
electrician before installation.
• Do not connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting
system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed
electrician for information with regards to proper grounding methods as required by the local electrical
code in your area.
•
•
Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires
to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could
cause serious injury or death from electric shock.
LED electronics can be damaged by electro static discharge (ESD) shock. Before installation, discharge
yourself by touching a grounded bare metal surface to remove this hazard. To avoid damage, do not touch
the LED module/components.
●
●
Before beginning assembly, installation or operation of this product, make sure all parts are present.
Compare parts with package contents list and diagram on this page. If any parts are missing or damaged,
do not attempt to assemble, install or operate the product. Contact Customer Service for replacement
parts. (1-866-237-9983)
Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape,
Wire Cutters, Safety Glasses, Ladder, Wire Stripper.
●
●
Non-replaceable LEDs.
If you are not familiar with state and local electrical codes, it is recommended that you consult with
a qualified electrician.
● Suitable for use in wet locations.
• Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to
avoid eye damage.
● Turn fixture on/off with wall switch or automatic timer.
● For use in 120V applications only.
INSTALLATION
HARDWARE
1) Thread knuckle through the cover plate (sold separately) and tighten the provided Hex Nut.
If installing to an In-Ground Fixture Mount (sold separately) follow the installation instructions
included with that product.
2) After making wiring connections (Illustration 1 below), attach the cover plate to the junction box.
3) To adjust Flood position, loosen Hex Nut and rotate fixture to desired position. Re-tighten Hex Nut
to secure.
4) To adjust Flood angle up or down, loosen the Arm Knuckle Screw. Position the fixture to the
desired position. Re-tighten Arm Knuckle Screw to secure.
5) Caulk around the Junction box cover plate and Threaded Knuckle, Arm Knuckle Joint and all
exposed fastener openings with a suitable RTV silicone caulking compound.
6) This fixture is equipped with a One Touch Light Color Selector located on the lower front
face of the fixture. To activate the color select feature, restore power to the fixture and
rapidly toggle the wall switch (or the breaker switch if no wall switch is being used) on and off
for approximately 7-10 seconds and then touch the once touch color selector button to select
desired color temperature.
*PLEASE NOTE: Selected color ,will be memory locked after 30 minutes. To reset, simply
repeat step 6.
Wiring:
Caution: Ensure that line voltage is compatible with fixture. (120V only)
1) Connect the black fixture lead to line voltage.
2) Connect the white fixture lead to common.
3) Connect the supply ground to the junction box grounding
screw or appropriate ground wire per applicable code.
Illustration 1
Wire Nuts
(3)
Hex Nut
(1)
(1)
Water Proof gasket /
Rubber Washer
WARNING: Turn off the power at circuit box or remove fuse
LOCATION: This product should be mounted to a threaded Junction Box Cover Plate
or a properly installed In-Ground Fixture Mount in accordance with local codes, ordinances or
the National Electric Code (NEC). Fixture to be permanently mounted.
MOUNTING:
(Note: Ensure Hex Nut is threaded onto Threaded Knuckle followed by Water Proof Gasket
prior performing Step 1)
●