Item No：PHGHG FOR OUTDOOR USE ONLY. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PACKAGE CONTENTS A Reflector B Damper C Upper Support D Wireguard E Glass Tube F Middle plate G Side Panel K Control box H Lower Support I Front Panel J Base PART A B C D E F G H I J K 2 DESCRIPTION Reflector Damper Upper Support Wireguard Glass Tube Middle plate Side Panel Lower Support Front Panel Base Control box QUANTITY 1 1 4 4 1 1 3 4 1 1 1
HARDWARE CONTENTS (shown actual size) Screw M3/16 AA attach to the regarding parts DD Fixing Bracket Qty. 4 BB Stability Ring EE (if avalable) Qty.1 AA battery FF Qty.1 Knob Qty. 1 CC Wheels GG Qty.1 set Rubber Ring Qty.1 SAFETY INFORMATION This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in these first few pages and is also located throughout the manual.
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS 1. Attach 1 set wheels(FF) to the base(J), if needed. 1 J 2 2. Attach the stability ring(DD) to the base (J),if avalable.
ASSEMBLY INSTRUCTIONS 3. Unsrew any pre installed (M3/16) screws(AA) first. Assemble the four lower supports (H) to the base (J) and middle plate（F）using the (M3/16) screws (AA). 3 H AA J 4. Unsrew any pre installed (M3/16) screws(AA) first. Assemble the four upper supports (C) to the lower supports (H) using the (M3/16) screws (AA). The damper (B) is then assembled to the upper supports (C) using the (M3/16) screws (AA).
ASSEMBLY INSTRUCTIONS 5. Unscrew（M3/16) 4pcs screws from the bottom of the middle plate(F). Install an AA battery(EE) into the control box. Assemble the control box(K) onto the bottom of middle plate using the (M3/16) screws. Note : The control knob is to face to the front of the heater where the magnet is installed in the middle plate. 5 K 6 6. Screw the winning screws,washers and the winning nuts to assemble the reflector(A) into the damper(B).
ASSEMBLY INSTRUCTIONS 7. Carefully install the glass tube (E) by lifting up and inserting through the center hole in the upper plate. Ensure the rubber ring(GG) is attached to the lower edge of the glass tube as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the middle plate. Check and ensure that the glass tube is positioned properly and is completely covering the center hole of the middle plate.
ASSEMBLY INSTRUCTIONS 9. Attach the three side panels (G) to the heater using the (M3/16) screws (AA). Note : 1. M3/16 screws from Step 3 unscrewed from lower supports. 2.Do not cover the front side where the control knob is. 9 G 10. Screw the knob (CC) onto the front panel (I). Attach the panel to the heater by inserting the two tabs into the slots on the base (J). Hook the chain (which is preassembled onto the front panel) into the hole in the front of the control box.
ASSEMBLY INSTRUCTIONS 11. Propane Only-Proper Hose Connection. Connect the hose to the hose connector in the control box. WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire. Always test the hose and connections for leak with soapy water at the end of all connections. 11 12. Connect hose and regulator to cylinder. The propane gas and cylinder are sold separately. Use a standard 20 lb. propane cylinder only.
ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Before Turning Gas Supply ON: 1.
OPERATION INSTRUCTIONS 3.Check for pilot flame through glass tube. If pilot does not light, turn control knob to ‘OFF’ position wait two minutes minimum and try again from the start. Some attempts may be necessary. 4.If the pilot alight, keep control knob pressed for 15 seconds then turn the control knob to ‘LOW’. 5.For maximum heat turn control knob to ‘HIGH’. 6.To turn heater off, turn control knob to ‘OFF’. 7.Close the vlave of the gas cylinder or the regulator after use.
OPERATION INSTRUCTIONS STORAGE: Between uses: Turn the control knob to “OFF” position. ● Turn LPG cylinder to “OFF” position. ● Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail, snow). ● If desired, cover heater to protect exterior surfaces and to help prevent dust and debris collecting in air passages. During periods of extended inactivity or when transporting: ● Turn the control knob to “OFF” position.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Pilot won’t light Air in gas line Note: Heater operates Low gas pressure with cylinder valve fully open at reduced efficiency below 40ºF (5ºC) Igniter fails Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas Turn cylinder valve OFF and replace cylinder Use match to light pilot;
