Data Sheet

Rev. 2/22
2
The Greensmaster
®
TriFlex
TM
is manufactured in
Tomah, WI ISO 9002 Certified Plant.
Greensmaster
®
TriFlex
®
3300/3320/3400/3420 Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
GREENSMASTER 3300
TriFlex, MODEL 04510
GREENSMASTER 3320
TriFlex Hybrid, MODEL 04530
GREENSMASTER 3400
TriFlex, MODEL 04520
GREENSMASTER 3420
TriFlex Hybrid, MODEL 04540
ENGINE
Briggs & Stratton® Vanguard®, 21 HP (15.6 kW) @ 3600 rpm, 2-cylinder,
air cooled, gasoline engine, governed to 2920 high idle, 1650 rpm low idle.
Displacement: 38.3 cu-in. (627 cc)
Kubota® D902, Tier 4i, 24.8 HP (18.5 kW) @ 3600 rpm, 3-cylinder, liquid cooled,
diesel engine, governed to 2880 high idle, 1560 rpm low idle. Displacement:
55.0 cu-in. (902 cc) Radiator: cooled with a 12-volt electric fan
FUEL CAPACITY
6 gallons (22.7 liter) capacity. 6 gallons (22.7 liter) capacity. Biodiesel ready up to B20
TRACTION DRIVE
2WD parallel hydrostatic or optional 3WD series-parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
GROUND SPEED
Forward-mowing speed is variable from 0-5 mph (0-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster TriFlex transport speed is 10 mph (16.1 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds.
CUTTING UNIT DRIVE
Single gear pump, valve block, series
reel drive to 3 reel motors.
48V-5400 watt air-cooled brushless
permanent magnet generator
in parallel with 48V 9Ah battery
set powers three 48V- 1100 watt
brushless permanent magnet reel
motors.
Single gear pump, valve block, series
reel drive to 3 reel motors.
48V-5400 watt air-cooled brushless
permanent magnet generator in
parallel with 48V 9Ah battery set
powers three 48V- 1100 watt brushless
permanent magnet reel motors.
AUTOMATIC CLIP CONTROL
N/A Yes N/A Yes
STEERING
Power steering. No-tool quick adjust steering arm position with power assist, allowing a wide range of operator sizes. Steering cylinder has a through shaft design
for precise straight line tracking.
ELECTRICAL SYSTEM
12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F
and 34 minutes reserve capacity at 85° F/25 amps draw.
50 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse
slot available for optional lights installation.
Maintenance-free 12-volt battery with 585 minimum cold cranking amps at
0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C)
60 amp alternator, circuit fused at 60 amps. Ignition switch/key. Seat switch.
High temperature engine shut down. Harness terminals, fuse slot, and console
switch location available for optional lights installation.
48-VOLT SYSTEM FOR
ELECTRIC REELS
N/A
4-12V 9Ah sealed, maintenance-free,
VRLA batteries. 48-volt system is
isolated from 12-volt including the
frame/chassis.
N/A
4-12V 9Ah sealed, maintenance-free,
VRLA batteries. 48-volt system is
isolated from 12-volt including the
frame/chassis.
CONTROLS
Ignition: Off/Run/Start. Throttle: Low - High Idle. Choke (AC only): Open /Closes choke plate. Parking Brake: Off - On. Traction Pedal: Rev/Neutral/Forward
Joystick: Raises/lowers reels also tap off feature for clean up pass. Functional Control Lever sets neutral/mow/transport limits for traction pedal.
Diagnostic Light: Indicates system faults to assist in resolving issues (04510 & 04520). InfoCenter
TM
Diagnostics (04530 & 04540).
GAUGES
Hour meter. Low oil pressure
warning light.
InfoCenter™: Onboard LCD shows
gauges, alerts/faults, service reminders,
electrical system diagnostics, low oil
pressure, alternator, engine hours,
engine rpm, voltage, functional control
status, parking brake applied, reel
speed setting, backlap control. Clip
control setting.
Hour meter, low oil pressure warning
light, alternator warning light (on if
not charging), glow plug indicator,
high engine temperature.
InfoCenter™: Onboard LCD shows
gauges, alerts/faults, service reminders,
electrical system diagnostics, low oil
pressure, alternator, engine hours,
engine rpm, voltage, functional control
status, parking brake applied, reel
speed setting, backlap control. Clip
control setting.
TIRES/WHEELS/PRESSURE
Three, 19 x 10.5 x 8, 4-ply rating pneumatic tubeless and demountable. Smooth tread. Tire pressure recommended: 12 - 18 psi front and rear.
BRAKES
Hand-actuated parking brake lever with two 6” (15.2 cm) diameter drum brakes mounted on the front wheel motors.
HYDRAULIC OIL
6.8 gallon (25.7 liter) tank 5.5 gallon (20.8 liter) tank 6.8 gallon (25.7 liter) tank 5.5 gallon (20.8 liter) tank
LEAK DETECTION
Equipped with Turf Guardian
TM
Leak
Detection System. System sounds an
alarm and turns on a warning light
with the loss of 3 to 5 ounces of
hydraulic oil.
Optional
SOUND LEVEL
80 dB(A) at operator’s ear under normal conditions. 84 dB(A) at operator’s ear under normal conditions.
OVERALL DIMENSIONS
Wheel Track: 50.5" (128.3 cm)
Wheel Base: 47" (119 cm)
Length: 98" (249 cm)
Width: 70.62" (179 cm) w/reels
Height: 80.83" (205 cm)
Wheel Track: 50.5” (128.3 cm)
Wheel Base: 47” (119 cm)
Length: 98” (249 cm)
Width: 70.84” (180 cm) w/reels
Height: 80.83” (205 cm)
Wheel Track: 50.5” (128.3 cm)
Wheel Base: 48.6” (123 cm)
Length: 98” (249 cm)
Width: 70.62” (179 cm) w/reels
Height: 80.83” (205 cm)
Wheel Track: 50.5” (128.3 cm)
Wheel Base: 48.6” (123 cm)
Length: 98” (249 cm)
Width: 70.84” (180 cm) w/reels
Height: 80.83” (205 cm)
WEIGHT
1161 lbs. (526 kg) 1257 lbs. (570 kg) 1286 lbs. (586 kg) 1406 lbs. (638 kg)
WIDTH OF CUT
59" (150 cm)
GROUND CLEARANCE
4.5” (11.4 cm)
CUTTING UNIT SUSPENSION
Double A-arm suspension utilizing sealed ball joints allows free cutting unit motion in pitch, roll, and yaw. The basket is directly mounted to the cutting unit
displacing weight evenly over both cutting unit rollers eliminating the carrier frame, roller and pull links. Lift in Turn: Provides a level cut from side to side of cutting
units regardless of turning angle (patented).
QUICK CONNECT CUTTING UNITS
Quick connect/disconnect feature for both the reel drive motor and cutting unit. No tools required.
REEL SPEED
Approximately 2050 RPM at 2850 engine RPM. Adjustable.
BACKLAPPING
Standard equipment.
OPTIONAL ACCESSORIES
Canopy, verticutters, greens rollers, dethatchers, oil cooler.
CERTIFICATION
Certified to meet ANSI specification B71.4 - 2004 and European CE standards.
WARRANTY
Two-year limited warranty. Refer to the Operator’s Manual for further details.