Instruction Manual PORTABLE WELDING TABLE For use with products having the following numbers: K5334-1 Register your product: www.lincolnelectric.com/register Authorized Service and Distributor Locator: www.lincolnelectric.com/locator Need Help? Call 1.888.935.3877 to talk to a Service Representative Hours of Operation: 8:00 AM to 6:00 PM (ET) Mon. thru Fri. Save for future reference Date Purchased After hours? Use “Ask the Experts” at lincolnelectric.
THANK YOU FOR SELECTING A QUALITY PRODUCT BY LINCOLN ELECTRIC. PLEASE EXAMINE CARTON AND EQUIPMENT FOR DAMAGE IMMEDIATELY When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received. SAFETY DEPENDS ON YOU Lincoln arc welding and cutting equipment is designed and built with safety in mind.
SAFETY SECTION A: WARNINGS CALIFORNIA PROPOSITION 65 WARNINGS WARNING: Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. • Always start and operate the engine in a well-ventilated area. • If in an exposed area, vent the exhaust to the outside. • Do not modify or tamper with the exhaust system. • Do not idle the engine except as necessary. For more information go to www.P65 warnings.ca.
SAFETY ELECTRIC SHOCK CAN KILL. ARC RAYS CAN BURN. 3.a. The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these “hot” parts with your bare skin or wet clothing. Wear dry, hole-free gloves to insulate hands. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 3.b.
SAFETY WELDING AND CUTTING SPARKS CAN CAUSE FIRE OR EXPLOSION. 6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available. 6.b.
SAFETY PORTABLE WELDING TABLE PORTABLE WELDING TABLE BEST PRACTICES The following guidelines will ensure proper usage of the portable welding table: SAFETY SAFETY PRECAUTIONS • WARNING • Do not attempt to use this equipment until you have thoroughly read all operating and maintenance manuals supplied with your machine. They include important safety precautions, operating and maintenance instructions and parts lists. • • FIRE OR EXPLOSION hazard • • Only use table for recommended applications.
PORTABLE WELDING TABLE TABLE OF CONTENTS SAFETY.........................................................................................................................................................................2 INSTALLATION .............................................................................................................................................SECTION A TECHNICAL SPECIFICATIONS .......................................................................................................
INSTALLATION PORTABLE WELDING TABLE INSTALLATION TECHNICAL SPECIFICATIONS GENERAL TABLE TOP DIMENSION 44 in. L x 21 in. W TABLE HEIGHT (ADJUSTABLE) 26.5 in. - 37.0 in. open legs, 8.5 in. closed legs. MAXIMUM WEIGHT CAPACITY 500 lbs when weight is evenly distributed, 350 lbs point load.
INSTALLATION PORTABLE WELDING TABLE PORTABLE WELDING TABLE ASSEMBLY Step 1 Parts needed • A (x 1) • C (x 1) • N (x 4) On FLAT surface, place table top Part C’s threaded studs through Part A’s tabbed slot hole. Lightly fasten with nuts (N). Do not tighten. FIGURE A.1 Step 3 Parts needed • E (x 1) • N (x 6) Slide bracket (E) onto assembly from Step 1. Lightly fasten nuts. FIGURE A.
INSTALLATION PORTABLE WELDING TABLE Step 5 Parts needed • F (x 1) • N (x 6) • O (x 4) Step 7 Gradually tighten all nuts to 50-56 in-lbs. Table top now complete. FIGURE A.7 On inner side of table, slide in side bracket (F) into threaded studs. Lightly fasten with lock nuts (N). Insert carriage bolts (O) through bracket and bottom lip of table top. Lightly fasten with nuts (N). FIGURE A.5 Step 8 Parts needed Step 6 Parts needed • K (x 1) • G (x 1) • L (x 1) • M (x 1) Assemble leg component.
INSTALLATION PORTABLE WELDING TABLE Step 9 Parts needed • J (x 1) • G (x 6) • H (x 4) • L (x 4) • M (x 4) Step 11 Parts needed • Leg Assembly (x 3) • N (x 9) • O (x 9) • P (x 3) Repeat step 8 with remaining three leg components. Repeat step 10 with remaining three legs of table. FIGURE A.10 Step 10 Parts needed • Leg Assembly (x 1) • N (x 3) • O (x 3) • P (x 1) Align leg bracket bolt holes so legs pivot along long sides of table.
INSTALLATION PORTABLE WELDING TABLE Step 13 Carefully turn table upright to stand onto legs. Check for FIGURE A.12 Step 14 Parts needed • Q (x 1) • R (x 1) • T (x 2) Fasten earth ground stud assembly. FIGURE A.
INSTALLATION PORTABLE WELDING TABLE OPTIONAL WHEEL KIT ASSEMBLY Wheel Kit Parts Key NAME A PART QTY 2 NAME B PART QTY 2 C 6 D 6 E 2 F 4 Step 1 Step 2 Parts needed Parts needed • B (x 2) • C (x 6) • D (x 6) • A (x 2) • E (x 2) • G (x 4) Attach bracket (B) with bolts (C) and nuts (D) onto leg bracket. Repeat on adjacent side. FIGURE A.14 Insert axle (E) into mounting bracket and clip (G) in wheels (A). Repeat on adjacent side. FIGURE A.15 NOTE: Bracket holes with flat sides to face out.
OPERATION PORTABLE WELDING TABLE OPERATION Safety Precautions The manufacturer does not accept any liability for damage to the product caused by a failure to follow the cations made to equipment or by negligence during installation, use, maintenance and repair of the product mentioned in the safety pages of this document and any corresponding accessories. require additional safety instructions. Immediately contact your supplier if you detect a potential hazard when using the product.
OPERATION PORTABLE WELDING TABLE USERS This product should only be used by authorized, trained and The Portable Welding Table has an earth ground bolt with two nuts that is to be used to connect the table to electrical earth ground. The stud can be mounted in the middle of any of the four sides of the table. Attach a copper lead from the earth ground stud to earth or building frame per local and national electrical codes.
OPERATION PORTABLE WELDING TABLE Use the windows on the sides of the table to store clamps. FIGURE B.5 The slots on the tabletop can be used for clamping or for cutting on the table surface without cutting the table itself. FIGURE B.7 USING THE TABLE Attach the WORK cable clamp from a welder or plasma cutter to the table close to where the welding or cutting is to occur. The side windows or slots are to be used for connecting the WORK clamp. pins, clamps, etc.
OPERATION PORTABLE WELDING TABLE The Portable Welding Table can be folded down for storage or transporting. The included handle can be mounted on any of the four sides of the table. NOTE: DO NOT EXCEED THE MAXIMUM WEIGHT LIMITS OF THE TABLE. For heavy weldments or loads, support the weight of object or load located on the table with hoists or tethers. • 500 LBS MAX, evenly dispersed. • 350 LBS MAX, at any point on the table surface. FIGURE B.10 FIGURE B.
Do not touch electrically live parts or :$51,1* 6SDQLVK $9,62 '( 35(&$X&,21 )UHQFK $77(17,21 *HUPDQ :$51X1* 3RUWXJXHVH $7(1d2 Keep flammable materials away. Wear eye, ear and body protection. Mantenga el material combustible Protéjase los ojos, los oídos y el electrode with skin or wet clothing. Insulate yourself from work and ground. No toque las partes o los electrodos bajo carga con la piel o ropa mojada. Aislese del trabajo y de la tierra.
Keep your head out of fumes. Use ventilation or exhaust to Turn power off before servicing. Do not operate with panel open or guards off. remove fumes from breathing zone. Los humos fuera de la zona de res- piración. Mantenga la cabeza fuera de los humos. Utilice ventilación o aspiración para gases. Gardez la tête à l’écart des fumées. Utilisez un ventilateur ou un aspira- Desconectar el cable de ali- mentación de poder de la máquina antes de iniciar cualquier servicio.
CUSTOMER ASSISTANCE POLICY The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time.
