Data Sheet

ManualsBrandsUnbranded ManualsActive ComponentsLinear IC - Op-amp LM358AMX/NOPB Multi-purpose SOIC 8

LM158-N, LM258-N, LM2904-N, LM358-N

www.ti.com

SNOSBT3H –JANUARY 2000–REVISED MARCH 2013

LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers

Check for Samples: LM158-N, LM258-N, LM2904-N, LM358-N

FEATURES

ADVANTAGES

• Available in 8-Bump DSBGA Chip-

• Two Internally Compensated Op Amps

Sized Package, (See AN-1112 (SNVA009))

• Eliminates Need for Dual Supplies

• Internally Frequency Compensated for Unity

• Allows Direct Sensing Near GND and V

OUT

Gain

Also Goes to GND

• Large DC Voltage Gain: 100 dB

• Compatible with All Forms of Logic

• Wide Bandwidth (Unity Gain): 1 MHz

• Power Drain Suitable for Battery Operation

(Temperature Compensated)

• Wide Power Supply Range: DESCRIPTION

The LM158 series consists of two independent, high

– Single Supply: 3V to 32V

gain, internally frequency compensated operational

– Or Dual Supplies: ±1.5V to ±16V

amplifiers which were designed specifically to operate

• Very Low Supply Current Drain (500

from a single power supply over a wide range of

μA)—Essentially Independent of Supply

voltages. Operation from split power supplies is also

Voltage

possible and the low power supply current drain is

independent of the magnitude of the power supply

• Low Input Offset Voltage: 2 mV

voltage.

• Input Common-Mode Voltage Range Includes

Application areas include transducer amplifiers, dc

Ground

gain blocks and all the conventional op amp circuits

• Differential Input Voltage Range Equal to the

which now can be more easily implemented in single

Power Supply Voltage

power supply systems. For example, the LM158

• Large Output Voltage Swing

series can be directly operated off of the standard

+5V power supply voltage which is used in digital

UNIQUE CHARACTERISTICS

systems and will easily provide the required interface

electronics without requiring the additional ±15V

• In the Llinear Mode the Input Common-Mode

power supplies.

Voltage Range Includes Ground and the

The LM358 and LM2904 are available in a chip sized

Output Voltage Can Also Swing to Ground,

package (8-Bump DSBGA) using TI's DSBGA

even though Operated from Only a Single

package technology.

Power Supply Voltage.

• The Unity Gain Cross Frequency is

Temperature Compensated.

• The Input Bias Current is also Temperature

Compensated.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (33 pages)

PAGE 1
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.
PAGE 2
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com Voltage Controlled Oscillator (VCO) These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 3
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 ABSOLUTE MAXIMUM RATINGS (1) (2) LM158/LM258/LM358 LM2904 LM158A/LM258A/LM3 58A Supply Voltage, V+ 32V Differential Input Voltage 26V 32V 26V −0.3V to +32V −0.
PAGE 4
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com ELECTRICAL CHARACTERISTICS V+ = +5.0V, unless otherwise stated Parameter Conditions LM158A Min Typ Input Offset Voltage (1) Input Bias Current IIN(+) or IIN(−), TA = 25°C, , TA = 25°C LM358A Max Min Typ LM158/LM258 Max Min Typ Units Max 1 2 2 3 2 5 mV 20 50 45 100 45 150 nA 2 10 5 30 3 30 nA V+−1.
PAGE 5
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 ELECTRICAL CHARACTERISTICS V+ = +5.0V, See (1), unless otherwise stated Parameter Conditions Large Signal Voltage Gain V+ = 15V, TA = 25°C, RL ≥ 2 kΩ, (For VO = 1V to 11V) Common-Mode TA = 25°C, Rejection Ratio VCM = 0V to V+−1.
PAGE 6
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com ELECTRICAL CHARACTERISTICS (continued) V+ = +5.0V, See(1), unless otherwise stated Parameter Output Current Conditions Source VIN+ = +1V, VIN− = 0V, V+ = 15V, VO = 2V Sink VIN− = +1V, VIN+ = 0V, V+ = 15V, VO = 2V LM158A Min Typ LM358A Max Min Typ LM158/LM258 Max Min Typ Units Max 10 20 10 20 10 20 mA 10 15 5 8 5 8 mA ELECTRICAL CHARACTERISTICS V+ = +5.
PAGE 7
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 ELECTRICAL CHARACTERISTICS (continued) V+ = +5.
PAGE 8
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS 8 Input Voltage Range Input Current Figure 1. Figure 2. Supply Current Voltage Gain Figure 3. Figure 4. Open Loop Frequency Response Common-Mode Rejection Ratio Figure 5. Figure 6.
PAGE 9
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Voltage Follower Pulse Response Voltage Follower Pulse Response (Small Signal) Figure 7. Figure 8. Large Signal Frequency Response Output Characteristics Current Sourcing Figure 9. Figure 10. Output Characteristics Current Sinking Current Limiting Figure 11. Figure 12.
PAGE 10
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 10 Input Current (LM2902 only) Voltage Gain (LM2902 only) Figure 13. Figure 14.
PAGE 11
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 APPLICATION HINTS The LM158 series are op amps which operate with only a single power supply voltage, have true-differential inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier operation is possible down to a minimum supply voltage of 2.3 VDC.
PAGE 12
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com CONNECTION DIAGRAM Figure 15. PDIP/CDIP/SOIC Package – Top View (See Package Number P, NAB0008A, or D) Figure 16. TO-99 Package – Top View (See Package Number LMC) Figure 17. 8-Bump DSBGA - Top View, Bump Side Down (See Package Number YPB0008AAA) TYPICAL SINGLE-SUPPLY APPLICATIONS (V+ = 5.0 VDC) Figure 18.
PAGE 13
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 Where: VO = V1 + V2 − V3 − V4 (V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC Figure 19. DC Summing Amplifier (VIN'S ≥ 0 VDC and VO ≥ 0 VDC) VO = 0 VDC for VIN = 0 VDC AV = 10 Figure 20.
PAGE 14
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com fo = 1 kHz Q = 50 Av = 100 (40 dB) Figure 21. “BI-QUAD” RC Active Bandpass Filter Figure 22. Fixed Current Sources Figure 23.
PAGE 15
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 Figure 24. LED Driver *(Increase R1 for IL small) VL ≤ V+ −2V Figure 25. Current Monitor Figure 26. Driving TTL VO = VIN Figure 27.
PAGE 16
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com Figure 28. Pulse Generator Figure 29. Squarewave Oscillator Figure 30. Pulse Generator HIGH ZIN LOW ZOUT Figure 31.
PAGE 17
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 IO = 1 amp/volt VIN (Increase RE for IO small) Figure 32. High Compliance Current Sink Figure 33. Comparator with Hysteresis *WIDE CONTROL VOLTAGE RANGE: 0 VDC ≤ VC ≤ 2 (V+ −1.5V DC) Figure 34.
PAGE 18
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com Figure 35. AC Coupled Inverting Amplifier Figure 36. Ground Referencing a Differential Input Signal Av = 11 (As Shown) Figure 37.
PAGE 19
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 fo = 1 kHz Q=1 AV = 2 Figure 38. DC Coupled Low-Pass RC Active Filter fo = 1 kHz Q = 25 Figure 39. Bandpass Active Filter Figure 40.
PAGE 20
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com Figure 41. Photo Voltaic-Cell Amplifier Figure 42. Bridge Current Amplifier Figure 43.
PAGE 21
LM158-N, LM258-N, LM2904-N, LM358-N www.ti.com SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 Figure 44.
PAGE 22
LM158-N, LM258-N, LM2904-N, LM358-N SNOSBT3H – JANUARY 2000 – REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision G (March 2013) to Revision H • 22 Page Changed layout of National Data Sheet to TI format ..........................................................................................................
PAGE 23
PACKAGE OPTION ADDENDUM www.ti.
PAGE 24
PACKAGE OPTION ADDENDUM www.ti.
PAGE 25
PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.
PAGE 26
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM2904ITP/NOPB DSBGA YPB 8 250 178.0 LM2904ITPX/NOPB DSBGA YPB 8 3000 LM2904MX SOIC D 8 2500 LM2904MX/NOPB SOIC D 8 LM358AMX SOIC D LM358AMX/NOPB SOIC LM358MX SOIC LM358MX/NOPB B0 (mm) K0 (mm) P1 (mm) 8.4 1.5 1.5 0.66 4.0 178.0 8.4 1.5 1.5 0.66 330.0 12.4 6.5 5.
PAGE 27
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2904ITP/NOPB DSBGA YPB 8 250 210.0 185.0 35.0 LM2904ITPX/NOPB DSBGA YPB 8 3000 210.0 185.0 35.0 LM2904MX SOIC D 8 2500 367.0 367.0 35.0 LM2904MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM358AMX SOIC D 8 2500 367.0 367.0 35.0 LM358AMX/NOPB SOIC D 8 2500 367.0 367.0 35.
PAGE 28
MECHANICAL DATA NAB0008A J08A (Rev M) www.ti.
PAGE 29
PAGE 30
PAGE 31
PAGE 32
MECHANICAL DATA YPB0008 D 0.5±0.045 E TPA08XXX (Rev A) D: Max = 1.337 mm, Min =1.276 mm E: Max = 1.337 mm, Min =1.276 mm 4215100/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.
PAGE 33
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.