Operator's Manual LM601 Landmark™ Permanent Blind Assembly Time 2-4 Hours Get parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind INTRODUCTION Landmark™ Permanent Blinds are engineered with you the hunter in mind. We appreciate your purchase of one of our world class products. Follow these few simple instructions and your blind will provide you many years of trouble-free pleasure. Instructions should be kept in a safe place and reviewed at least annually.
Operator's Manual Landmark™ Permanent Blind FRAME ASSEMBLY INSTRUCTIONS Tools needed – two 10mm wrenches IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations completely until all parts are assembled together! Finger tighten plus one turn of a wrench only! This will temporarily hold the lock nut on the bolt while helping alignment of all parts! After all parts are assembled together, all nut & bolt combinations must be completely tightened. FIGURE 1 1.
Operator's Manual Landmark™ Permanent Blind FIGURE 2 5. Slide the four C1 poles into the HUB1 corners so that the snap buttons secure pieces together. SEE FIGURE 2. 6. Attach the four HUB2 corners to C1 poles so that the snap buttons secure pieces together. PAY ATTENTION TO ORIENTATION OF THE HUB2 CORNERS! SEE FIGURE 2. 4 Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind FIGURE 3 7. Slide each of the three D2 poles into an E2 pole so that the snap button secures both pieces together. SEE FIGURE 3. 8. Slide the three assembled D2 and E2 poles into the HUB2 corners. These do not attach with snap buttons and will be secured together with hardware in a later step. SEE FIGURE 3. Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind 20 22 20 22 FIGURE 4 9. Attach each of the eight F1 poles to the bottom and middle tiers of the blind frame using two M6 x 35mm bolts (20) and M6 nuts (22). Make sure upper bolts are securing the D2 and E2 poles along with the F1 poles. SEE FIGURE 4. NOTE: PAY ATTENTION TO THE ORIENTATION OF THE BOLTS! THE HEAD OF THE BOLT MUST BE ON THE OUTSIDE OF THE FRAME. THIS HELPS PREVENT UNNECESSARY WEAR ON THE SKIN WHEN FULLY ASSEMBLED.
Operator's Manual Landmark™ Permanent Blind Through Hole Closer to HUB3 than HUB2 Through Hole Closer to HUB3 than HUB2 FIGURE 5 10. Slide two G1 poles into HUB2 corners on the door side of the blind so that the snap buttons secure pieces together. It is critical that the G1 poles are oriented such that snap buttons are facing each other and each through hole is located closer to the HUB3 corners than the HUB2 corners. SEE FIGURE 5. 11.
Operator's Manual Landmark™ Permanent Blind Through Hole Closer to HUB3 than HUB2 Through Hole Closer to HUB3 than HUB2 FIGURE 6 12. Slide remaining two G1 poles into the other HUB2 corners so that snap button secures pieces together. It is critical that the G1 poles are oriented such that snap buttons are facing each other and each through hole is located closer to the HUB3 corners than the HUB2 corners. SEE FIGURE 6. 13.
Operator's Manual Landmark™ Permanent Blind FIGURE 7 14. Slide the two H1 poles into the two I1 poles so that snap buttons secure pieces together. SEE FIGURE 7. 15. Slide assembled H1 and I1 poles into HUB3 corners so that snap buttons secure pieces together. PAY ATTENTION TO THE ORIENTATION OF THE TABS ON H1 AND I1 POLES SO THAT THEY POINT UPWARD. SEE FIGURE 7. Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind FIGURE 8 16. Slide remaining two A1 poles into remaining two B1 poles so that snap buttons secure pieces together. SEE FIGURE 8. 17. Slide assembled A1 and B1 poles into HUB3 corner so that snap buttons secure pieces together. You should now have the top tier frame of the blind assembled. SEE FIGURE 8. 10 Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind 20 20 22 FIGURE 9 18. Attach the four J1 poles by one end to the horizontal through holes on the four assembled H1 and I1 poles using four M6 x 35mm bolts (20) and M6 nuts (22). Hand tighten only at this time. SEE FIGURE 9. 19. Attach the four K1 poles by the end with the hole, not the slot, to the vertical through holes on the four assembled A1 and B1 poles using four M6 x 35mm bolts (20) and M6 nuts (22). Hand tighten only at this time. SEE FIGURE 9.
Operator's Manual Landmark™ Permanent Blind 20 22 FIGURE 10 20. Attach each set of J1 and K1 poles to the four G1 poles with four M6 x 35mm bolts (20) and M6 nuts (22). Make sure the J1 poles are between the K1 and G1 poles. Tighten all loose hardware at this time. DO NOT OVERTIGHTEN TO PREVENT CRUSHING TUBING! SEE FIGURE 10. 12 Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind 19 22 FIGURE 11 21. Slide the four L1 poles into the four M1 poles and set aside. SEE FIGURE 11. 22. Slide the three N1 poles into the three O1 poles so that snap buttons secure pieces together and set aside. 23. Attached assembled L1 and M1 poles to one assembled N1 and O1 pole using the four M6 x 50mm bolts (19) and M6 nuts (22). SEE FIGURE 11. NOTE: PAY ATTENTION TO THE ORIENTATION OF THE BOLTS! THE HEAD OF THE BOLT MUST BE ON THE TOP OF THE FRAME.
Operator's Manual Landmark™ Permanent Blind 21 22 23 FIGURE 12 24. Attach remaining two assembled N1 and O1 poles to the ends of the L1 and M1 poles using eight M6 x 30mm bolts (21) and M6 nuts (22). SEE FIGURE 12. NOTE: PAY ATTENTION TO THE ORIENTATION OF THE BOLTS! THE HEAD OF THE BOLT MUST BE ON THE TOP OF THE ROOF FRAME. THIS HELPS PREVENT UNNECESSARY WEAR ON THE SKIN WHEN FULLY ASSEMBLED. 25. Insert the four eave end plugs (23) into the ends of the N1 and O1 poles. SEE FIGURE 12.
Operator's Manual Landmark™ Permanent Blind FIGURE 13 26. Attach assembled roof to blind structure using eight M6 x 35mm bolts (20) and M6 nuts (22). PAY ATTENTION TO THE ORIENTATION OF THE ROOF! THE ROOF ATTACHES ON THE INSIDE OF THE HUB3 CORNER TABS. SEE FIGURE 13. NOTE: TIGHTEN ANY LOOSE HARDWARE AT THIS TIME. DO NOT OVERTIGHTEN TO PREVENT CRUSHING TUBING! Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind SKIN ASSEMBLY INSTRUCTIONS 1. Lay out all sewn components and familiarize yourself with them. Pay special attention to the back wall panel and the two side wall panels as they look similar at first glance but are different. The back wall panel has a hook and loop attachment strip sewn across the entire width of panel at the top. You can also identify the panels by sewn on tags on the inside near the window. 2.
Operator's Manual Landmark™ Permanent Blind FIGURE 16A FIGURE 16B FIGURE 16C Hook and Loop Strap D-ring Strap FIGURE 17 6. Hang the back wall panel (29) on the back side of the assembled steel frame (opposite the door opening) by connecting the top clip of one of the window poles to the top of the frame near the K1 brace. Connect the bottom clip of the same window pole to the bottom frame by angling the pole towards the center of the window panel, and once attached, sliding outwards towards F1 brace.
Operator's Manual Landmark™ Permanent Blind A D-ring Strap Hook and Loop Strap FIGURE 18 7. Hang the left front wall panel (31) on the front side of assembled steel frame by connecting the top clip of the pole to the top of the frame near the K1 brace. Connect the bottom clip of the pole to the bottom frame by angling the pole towards the center of the door opening, and once attached, sliding outwards towards F1 brace. Repeat for right front wall panel (30).
Operator's Manual Landmark™ Permanent Blind A B C FIGURE 19 10. Drape the roof panel (25) over the assembled roof frame. Secure the hook and loop attachment strips on the front and the back of roof panel to the strips on the front and back wall panels. SEE FIGURE 19A. NOTE: ADJUST AND REDO AS NECESSARY TO TAKE OUT AS MUCH SLACK IN THE FABRIC AS POSSIBLE. 11. Wrap the edge corner flaps of the roof panel around the eave corners of the frame assembly and secure with hook and loop attachment squares.
Operator's Manual Landmark™ Permanent Blind Clip Tether Buckle Clip Shoo ting R Top Frame Pole Tether Buckle Window Pole ail Mid Frame Pole Tether Buckle FIGURE 20 FIGURE 21 13. Locate the three horizontal window panels with shooting rail sleeves (27) and the three S1 poles. Insert an S1 pole into the shooting rail sleeve on each window panel. SEE PARTS BREAKDOWN (Page 25). 14. Locate the other three horizontal window panels (28) and the six vertical window panels (35).
Operator's Manual Landmark™ Permanent Blind A D B C FIGURE 22 19. Locate all of the tether straps (37). Wrap strap around angled corner brace and then send male buckle through the looped end of the strap. Pull tight to snug tether strap to angled corner brace. Insert the male buckle into the female buckle attached to the window panel. SEE FIGURE 22. 20. Repeat for all window and door panels.
Operator's Manual Landmark™ Permanent Blind Sewn Strap Corkscrew Stake FIGURE 23 GROUND STAKE INSTRUCTIONS 1. On the inside of the blind, screw corkscrew stake into ground near corner. SEE FIGURE 23. 2. Take loop end of a sewn strap and slide onto corkscrew stake. SEE FIGURE 23. 3. Wrap opposite end of sewn strap around closest D2 or E2 horizontal frame pole and feed end down through both D-rings. 4. Send end of sewn strap up and over the bottom D-ring and up and through the top D-ring.
Operator's Manual Landmark™ Permanent Blind ONE YEAR LIMITED WARRANTY RETI., warrants this product under a one-year limited warranty to be free from defects in materials or workmanship or both for a period not exceeding twelve consecutive months from the date of original purchase by the first retail consumer or commercial end user. “Consumer use” means personal recreational use by a retail consumer.
Operator's Manual Landmark™ Permanent Blind PARTS BREAKDOWN 23 10 15 12 3 18 19 17 16 21 23 22 11 2 14 13 9 6 5 8 4 20 1 2 3 7 20 KEY # PART # DESCRIPTION 1 22864 BASE HUB "HUB1" 4 KEY # 2 22930 HORIZONTAL SUPPORT FEMALE "B1" 6 13 22879 UPPER CROSS BRACE "J1" 4 3 22932 HORIZONTAL SUPPORT MALE "A1" 6 14 22880 CORNER CROSS BRACE "K1" 4 4 22934 LOWER VERTICAL SUPPORT "C1" 4 15 22881 ROOF TUBE MALE "L1" 4 5 22868 MIDDLE HUB "HUB2" 4 16 22882 ROOF TUBE FEMALE
Operator's Manual Landmark™ Permanent Blind PARTS BREAKDOWN 25 35 28 33 26 24 27 35 29 32 31 34 34 26 30 KEY # PART # DESCRIPTION QTY.
Operator's Manual Landmark™ Permanent Blind NOTES 26 Check for parts online at www.HuntRiversEdge.
Operator's Manual Landmark™ Permanent Blind OTHER GREAT PRODUCTS BY RIVERS EDGE TREESTANDS With the Landmark 10 foot tower, the Landmark Permanent Blind can be used in an elevated position for optimal vantages. It is constructed from sturdy, powder-coated steel. The angled entrance and exit ladder has large steps accompanied by handrails along the top. An additional platform outside the door aides in a smooth entrance/exit. Additional feet anchors and a center anchor is included.
WE ARE HUNTERS Rivers Edge® Treestands, Inc. 1160 Eighth Avenue, PO Box 755 Cumberland, WI 54829 Phone: 800-450-EDGE (3343) Fax: 715-822-2124 www.HuntRiversEdge.com *All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.
