Warranty

4
!!ATTENTION INSTALLER!!
Before taking the bath indoors for installation, thoroughly inspect bath for:
Shipping Damage: Report shipping damage to the carrier immediately. DO NOT INSTALL A
DAMAGED BATH. Signature Bath is not responsible for damage that occurred during transit.
Factory Defect: Manufacturing defects must be reported to Signature Bath before installation.
Defects or damage claimed after installation are not covered under the warranty.
Measurement Variances: Each Signature Bath is hand crafted which may result in slight variations
during the manufacturing process. The manufacturer recommends measuring the bath to determine
actual cut-out dimensions. Signature Bath is not responsible for preparatory materials or labor costs
associated with variations in the manufacturing process..
This bath must be tested for operation and leaks prior to placement and enclosure. Failure to do so will void the warranty. Signature Baths
are water tested at the manufacturing facility and found to be fully operational and leak-free prior to shipping. Freight, handling and site
exposure may adversely affect the baths condition. It is the responsibility of the installer to inspect the bath shell and components for
defects and to test the bath prior to installation. This bath is intended for indoor use only and is warranted for indoor installation in a
climate controlled environment only.
TESTING YOUR BATH:
1. To protect the bath, lay a clean heavy drop cloth on a at surface where the bath can be drained easily after testing, like a driveway.
2. Remove the packing materials being careful not to scratch or damage the surface. Inspect the bath to make sure the model, color and
features in the bath received match the bath that was ordered exactly.
3. Carefully place the bath on the drop cloth. Do not use the plumbing harness or electrical components to lift the bath.
4. Seal the drain with tape.
5. Fill the bath until the water level is approximately 1/2 full and allow bath to stand for ve minutes.
6. Check for leaks by examining the area underneath and surrounding the bath.
Do not install the bath if it leaks. Follow the troubleshooting steps or call Signature Bath Customer Care at 844-894-6659 for assistance.
Signature Bath is not responsible for leaks claimed after the bath is installed or any costs associated with damage caused by a leak, removal
or reinstallation of the bath, loss of materials or labor charges.
Do not store the bath in temperatures below 32º F. To prevent scratching, chipping and other damage during construction and installation,
the bath should be stored in the box until it is installed. During construction, a protective cover should be placed on the bath. Do not
store materials or place heavy objects in the bath. Do not stand in the bath. Damage that occurs on the job site can often be repaired at the
owner’s expense but is not covered under the manufacturer’s warranty.
INSTALLATION NOTES
Bath Enclosure Notes
Installation must be made in compliance with state and local codes at the time of installation.
Plumbing Notes
Installation and connections must be made in compliance with UPC and local plumbing codes in place at the time of installation. A plumber
should install the drain, overow and other xtures not included with the purchase of a Signature Bath following their manufacturer’s
instructions. Inspect for leaks prior to installing the bath enclosure.
Site Preparation Notes
Your Signature Bath must be installed on a level sub-oor that can support the combined weight of the bath, the water and the bathers.
The full bottom of the bath must be on a level surface. The sub-oor should be inspected and repaired prior to installation of the bath if
necessary. The manufacturer recommends sealing the sub-oor prior to installing the bath to reduce the risk of water damage.
Framing Notes:
Do not begin building any structure until the bath arrives. Measure the bath when it arrives to determine the measurements for the
structure. Because Signature Baths are handcrafted, the actual dimensions may dier slightly from the manufacturers published
specications. The framing must include unrestricted access to components. Signature Bath will not authorize service if access is restricted.
Access from a crawl space is considered restricted and may result in denial of warranty claims.
The GFCI is not included with the bath. The circuit must be a (3) three-wire circuit hard wired from the main power supply. Install the outlet
on the stud wall at least 4” above the oor. Your bath is equipped with a 36” cord with a grounded plug on the pump. Do not remove the
grounding pin or alter the cord in any way.
Important: Unauthorized modication may cause unsafe operation and poor performance. Making modications may adversely aect
performance and make operation unsafe. Signature Bath shall not be liable under its warranty of otherwise for personal injury or damage
that is the result of unauthorized modication.
4