42nd Street by Hampton Bay ®
52” 42nd Street Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 UL Model No. 515-126 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No. Installing the Light Kit . . . . . . . . . . . . . . 9 Operating Your Transmitter . . . . . . .
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding 2.
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: 5 2 9 A B 10 1 6 3 7 8 4 1. 2. 3. 4. 5. 6. Set of blades (4) Canopy assembly Ball/downrod assembly Coupling cover Fan motor assembly Mounting plate WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-800-527-0998. 2 7. 8. 9. 10. 11. 12.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Ceiling Mounting Plate Figure 3 Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. WARNING Cross Pin FAILURE TO PROPERLY INSTALL COTTER PIN AS NOTED IN STEP 5 COULD RESULT IN FAN LOOSENING AND POSSIBLY FALLING. Hanger Ball Downrod 1. Remove the canopy cover from the canopy by turning the cover counter clockwise. (Figure 5) Hanger Bracket 2.
6. Slip coupling cover, canopy cover and canopy onto downrod. Carefully reinstall hanger ball onto rod being sure that cross pin is in correct position, set screws are tighten and wires are not twisted. (Figure 9) Motor Wires Ball/Downrod Assembly Pin in Locked Positioon Installing Fan to the Electrical Box UL Listed Outlet Box WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY.
Making the Electrical Connections receiver. Secure the wire connections with the plastic wire connecting nuts provided. Frequency Switch WARNING TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE MAIN FUSE BOX BEFORE WIRING. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units.
WARNING BLACK BLACK WHITE SUPPLY CIRCUIT Ground Conductor Outlet Box GREEN WHITE WHITE BLUE BLACK BLACK BLUE WHITE Green Ground Lead Ground to Downrod CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. EXCEPT FOR THE GROUND WIRE. WARNING MAKE SURE THE TAB ON THE HANGING BRACKET PROPERLY SITS IN THE GROOVE IN THE HANGER BALL BEFORE ATTACHING THE CANOPY TO THE BRACKET BY TURNING THE HOUSING UNTIL IT DROPS INTO PLACE.
Attaching the Fan Blades Blade Balancing 1. Rotate motor until holes become visible through the motor access window. Align the holes from the blade to the holes from the motor and secure in place with screws and fiber washers provided. (Fig. 16) The following procedure should correct most fan wobble. Check after each step. 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal.
Installing the Mounting Plate 1. Remove 1 of the 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) Installing the Light Kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. 2.
4. Install 100W halogen bulb (included). (Fig. 20) 5. Raise glass shade up against bottom of fan housing and secure it to fan by turning glass clockwise until snug. Do not overtighten. (Fig. 20) 6. Restore power, your light kit is ready for operation. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE.
Operating Your Transmitter Installing the Battery: Restore power to the ceiling fan and test for proper operation. Install 12V MN21/A23 battery (included), to prevent damage to transmitter, remove the battery if not used for long periods. 1. "HI, MED, LOW" buttons: These three buttons are used to set the fan speed as follows: LOW=Low speed, MED= Medium speed HI=High speed ( WARNING: May explode or leak if recharged, disposed of in fire or dissected. Do not ingest.) Figure 22 2.
Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. Installing the Transmitter Holder The Reverse switch is located on the top of motor housing. Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. 1. Remove the two plugs from the holder. Note that the plugs have unique tabs that allows them to fit only in one hole. (Fig. 25) 2. Attach the holder with the two screws provided.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. 3.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 52" MED. HIGH 120 WATTS RPM CFM 0.35 14.6 69.09 1940.38 0.48 37.55 125.43 3765.32 0.49 58.3 162.33 5026.87 These are approximate measures. They do not include Amps and Wattage used by the light kit. Distributed by Home Depot U.S.A., Inc. 2455 Paces Ferry Rd., N.W. Atlanta, GA 30339 14 N.W. G.W. C.F. 8.73 kgs (19.21 lbs) 9.65 kgs (21.23 lbs) 1.
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
