250 903 Biscay Bay 52 in Ceiling Fan Owner’s Manual Biscay Bay Ventilador de Techo de 1,32m Manual del Propietario
Biscay Bay by Hampton Bay ®
52” Biscay Bay Ceiling Fan by Hampton Bay Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will naturally weather and fade. Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 Model No. 250-903 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No.
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding 2.
Unpacking Your Fan 2a 2b 2c Unpack your fan and check the contents. You should have the following items: 5 7 A B C D 8 1 3 9 6 4 1. 2a. 2b. 2c. 3. 4. Set of blades (5) Ceiling canopy Hanger bracket Canopy cover Ball/downrod assembly Coupling cover WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-800-527-0998. 2 10 5. 6. 7. 8. 9. 10. Fan motor assembly Blade holders (5) Mounting plate Switch housing Pull chain and fob Downrod rubber cover A.
Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Ceiling Mounting Plate Figure 3 Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. WARNING Cross Pin FAILURE TO PROPERLY INSTALL COTTER PIN AS NOTED IN STEP 5 COULD RESULT IN FAN LOOSENING AND POSSIBLY FALLING. Hanger Ball Downrod 1. Remove the canopy cover from the canopy by turning the cover counter clockwise. (Figure 5) Hanger Bracket 2.
6. Slip coupling cover, canopy cover and canopy onto downrod. Carefully reinstall hanger ball onto rod being sure that cross pin is in correct position, set screws are tighten and wires are not twisted. (Figure 9) 7. Place downrod rubber cover onto the hanger ball, pass wires through the downrod rubber cover and slip onto hanger ball.
If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire nuts supplied with your fan. Secure the wire nuts with electrical tape. Make sure there are no loose strands or connections. 1. Connect the ground conductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan (Figure 12). 6.
Ground Conductor BLACK WHITE SUPPLY CIRCUIT Ground Conductor Outlet Box Outlet Box Green Ground Lead Green Ground Lead Ground to Downrod Figure 13 BLUE BLACK WHITE GREEN BLUE BLACK WHITE GREEN BLACK WHITE SUPPLY CIRCUIT Ground to Downrod Figure 14 7
Finishing the Fan Installation 1. Tuck connections neatly into ceiling outlet box. 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 15) Outlet Box Hanger Bracket Screws Canopy 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
Attaching the Fan Blades CAUTION Motor MOTOR IS SHIPPED WITH RUBBER PACKING MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE 5 RUBBER PACKING MOUNTS FROM FAN MOTOR ASSEMBLY AND DISCARD PRIOR TO ATTACHING BLADE ARMS. (FIG. 16) 1. Attach blades to blade arm using the screws with fiber washers provided. (Fig. 17) Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. 2. Tighten each screw securely starting with the center screw.
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 19.
Installing the Mounting Plate Installing the Switch Housing 1. Remove 1 of 3 screws from the mounting ring CAUTION and loosen the other 2 screws. (Do not remove) BEFORE STARTING INSTALLATION, DISCON2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig.
Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION. Turn on the power and check the operation of your fan. There are two pull chains available in your fan: Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect as shown in Figure 22. This allows you to set your air conditioner on a higher setting without affecting your comfort. 1.
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning. Use only a soft brush or lint-free cloth to avoid scratching the finish.
Specifications FAN SIZE SPEED VOLTS AMPS LOW 52" MED. HIGH 120 WATTS RPM CFM 0.27 16.31 84 1905.31 0.39 33.30 114 2998.36 0.53 63.01 159 4351.48 These are approximate measures. They do not include Amps and Wattage used by the light kit . Distributed by Home Depot U.S.A., Inc. 2455 Paces Ferry Rd., N.W. Atlanta, GA 30339 14 N.W. G.W. C.F. 9.87 kgs (21.71 lbs) 10.92 kgs (24.02 lbs) 1.
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
