Information
Table Of Contents
- A. Overview
- 1. Getting started
- 1.1 The BME688 Gas Sensor
- 1.2 Example: Coffee vs. Normal Air
- 1.3 A Few Things To Keep In Mind
- 1.4 Step 1: Record Normal Air
- 1.5 Step 2: Record Espresso Coffee
- 1.6 Step 3: Record Normal Air Again
- 1.7 Step 4: Record Filter Coffee
- 1.8 Step 5: Import & Label The Data
- 1.9 Step 6: Create New Algorithm and Classes
- 1.10 Step 7: Train And Evaluate The Algorithm
- 1.11 Step 8: Export The Algorithm
- 1.12 Conclusion
- 2. Introduction
- 2.1 What is it about? – An analogy
- 2.2 Why the BME688?
- 2.3 What is a use case for a gas sensor?
- 2.4 What is special about the BME688 gas sensor?
- 2.5 How can I evaluate BME688 performance for a specific use case?
- 2.6 How can I use the results for my product development?
- 3. Glossary
- 3.1 Sensor Board
- 3.2 Measurement Session
- 3.3 Algorithm
- B. Process Steps
- 1. Configure Board
- 1.1 Overview
- 1.2 Board Type
- 1.3 Board Mode
- 1.4 Heater Profile
- 1.5 Duty Cycle
- 1.6 Board Layout
- 2. Record Data
- 2.1 Overview
- 2.2 Start recording
- 2.3 During recording
- 2.4 End recording
- 3. Import Data
- 3.1 Overview
- 3.2 Data Overview
- 3.3 Board ID
- 3.4 Board Type
- 3.5 Board Mode
- 3.6 Session Name
- 3.7 Session Date
- 3.8 Specimen Data
- 4. Collect Specimens
- 4.1 Overview
- 4.2 Label
- 4.3 Comment
- 4.4 Session
- 4.5 Start & End Time
- 4.6 Duration
- 4.7 Cycles Total
- 4.8 Cycles Dropped
- 4.9 Remaining Cycles
- 4.10 Board Configuration
- 4.11 Board ID
- 4.12 Board Type
- 4.13 Board Mode
- 4.14 Show Configuration
- 5. Train Algorithms
- 5.1 Overview
- 5.2 Name
- 5.3 Created
- 5.4 Classes
- 5.5 Class Name & Color
- 5.6 Common Data
- 5.7 Data Balance
- 5.8 Data Channels
- 5.9 Neural Net
- 5.10 Training Method
- 5.11 Max. Training Rounds
- 5.12 Data Splitting
- 6. Evaluate Algorithms
- 6.1 Overview
- 6.2 Confusion Matrix
- 6.3 Accuracy
- 6.4 Macro-averaged F1 Score
- 6.5 Macro-averaged False Positive Rate
- 6.6 Training Data
- 6.7 Test Data
- 6.8 Additional Testing
- 2.1
Bosch Sensortec | BME AI-Studio Documentation 27 | 49
Modifications reserved | Data subject to change
without notice Document number: BST-BME688-AN001-00
2.2 Start recording
Insert the SD card into the BME board. The SD card slot is on the top side of the BME board. Insert the card with its
contacts facing towards the upper circuit board.
Connect the BME board to power with an micro USB cable. Once the board is connected to power, it will automatically
turn on and start recording. The red LED next to the USB connector should blink every two seconds. If it blinks rapidly,
the board is not recording.