Information
Table Of Contents
- A. Overview
- 1. Getting started
- 1.1 The BME688 Gas Sensor
- 1.2 Example: Coffee vs. Normal Air
- 1.3 A Few Things To Keep In Mind
- 1.4 Step 1: Record Normal Air
- 1.5 Step 2: Record Espresso Coffee
- 1.6 Step 3: Record Normal Air Again
- 1.7 Step 4: Record Filter Coffee
- 1.8 Step 5: Import & Label The Data
- 1.9 Step 6: Create New Algorithm and Classes
- 1.10 Step 7: Train And Evaluate The Algorithm
- 1.11 Step 8: Export The Algorithm
- 1.12 Conclusion
- 2. Introduction
- 2.1 What is it about? – An analogy
- 2.2 Why the BME688?
- 2.3 What is a use case for a gas sensor?
- 2.4 What is special about the BME688 gas sensor?
- 2.5 How can I evaluate BME688 performance for a specific use case?
- 2.6 How can I use the results for my product development?
- 3. Glossary
- 3.1 Sensor Board
- 3.2 Measurement Session
- 3.3 Algorithm
- B. Process Steps
- 1. Configure Board
- 1.1 Overview
- 1.2 Board Type
- 1.3 Board Mode
- 1.4 Heater Profile
- 1.5 Duty Cycle
- 1.6 Board Layout
- 2. Record Data
- 2.1 Overview
- 2.2 Start recording
- 2.3 During recording
- 2.4 End recording
- 3. Import Data
- 3.1 Overview
- 3.2 Data Overview
- 3.3 Board ID
- 3.4 Board Type
- 3.5 Board Mode
- 3.6 Session Name
- 3.7 Session Date
- 3.8 Specimen Data
- 4. Collect Specimens
- 4.1 Overview
- 4.2 Label
- 4.3 Comment
- 4.4 Session
- 4.5 Start & End Time
- 4.6 Duration
- 4.7 Cycles Total
- 4.8 Cycles Dropped
- 4.9 Remaining Cycles
- 4.10 Board Configuration
- 4.11 Board ID
- 4.12 Board Type
- 4.13 Board Mode
- 4.14 Show Configuration
- 5. Train Algorithms
- 5.1 Overview
- 5.2 Name
- 5.3 Created
- 5.4 Classes
- 5.5 Class Name & Color
- 5.6 Common Data
- 5.7 Data Balance
- 5.8 Data Channels
- 5.9 Neural Net
- 5.10 Training Method
- 5.11 Max. Training Rounds
- 5.12 Data Splitting
- 6. Evaluate Algorithms
- 6.1 Overview
- 6.2 Confusion Matrix
- 6.3 Accuracy
- 6.4 Macro-averaged F1 Score
- 6.5 Macro-averaged False Positive Rate
- 6.6 Training Data
- 6.7 Test Data
- 6.8 Additional Testing
- 2.1
Bosch Sensortec | BME AI-Studio Documentation 30 | 49
Modifications reserved | Data subject to change
without notice Document number: BST-BME688-AN001-00
3. Import Data
3.1 Overview
After you recorded data with the BME board, it is now time to import the data into the application. During import, you can
verify the data and define your specimens. You can import several measurements and
collect everything in your
specimen collection, before later proceeding to train algorithms. You can import data into a new project or into existing
projects.
Access files on SD card
After your measurements, take the SD card out of the BME board. Access the files on the SD card from your computer
via an SD card reader.
Please note
If you do not see any data on the SD card, it is likely your board needs to be configured. To create a configuration file
for your board, please see configure board.
Importing raw data
Open the application and create a new project by clicking Create new project on the welcome screen. Alternatively,
you can open the menu and select New project.... Next, a file dialogue opens. Please select, where you want to
save your new project.
If you want to import data into an existing project, just open the project and switch to your Specimen Collection.