Instructions / Assembly

ManualsBrandsUnbranded ManualsPlayground Sets & EquipmentPegasus Outdoor Music Playset Accessory

PEGASUS

The Pegasus is a beautiful sounding, resonated metallophone

made with anodized aluminum bars. It has keys from both the

A minor and C major pentatonic scales. There is a lot of sound

and fun to be had with this instrument.

(LH) A MINOR / (RH) C MAJOR PENTATONIC

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

FREENOTES HARMONY PARK. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

FREENOTES HARMONY PARK IS

PROHIBITED.

FREENOTES HARMONY PARK

194 BODO DRIVE, UNIT F

DURANGO CO 81303

TEL: (970) 375-7825

FAX: (970) 247-0856

EMAIL: INFO@FREENOTESHARMONYPARK.COM

WWW.FREENOTESHARMONYPARK.COM

SHEET 1 OF 6

SCALE: 1:16

PRODUCT SHEET / INSTALLATION GUIDE

PEGASUS 2016

Summary of content (6 pages)

PAGE 1
PEGASUS The Pegasus is a beautiful sounding, resonated metallophone made with anodized aluminum bars. It has keys from both the A minor and C major pentatonic scales. There is a lot of sound and fun to be had with this instrument. (LH) A MINOR / (RH) C MAJOR PENTATONIC 3 47 4 " 7 18 8 " 1 12 8 " FREENOTES HARMONY PARK 194 BODO DRIVE, UNIT F DURANGO CO 81303 TEL: (970) 375-7825 FAX: (970) 247-0856 EMAIL: INFO@FREENOTESHARMONYPARK.COM WWW.FREENOTESHARMONYPARK.
PAGE 2
MOUNTING OPTION IDENTIFICATION: This instrument is offered with various mounting options. Identify your option below and follow installation instructions on the following sheets.
PAGE 3
RECYCLED AND STEEL POST IN-GROUND INSTALLATION PROCEDURES Step 1: Excavate two 10" diameter hole, 36" deep, and 32" on center at the installation location. Contractor can modify post to desired height. Post Length = Frost Depth (36" Recommended) + Finished Height (Refer to Height Guideline) Step 2: Lower the posts into the excavated holes. Step 3: Refer to sheet 6 for installation of instrument to posts.
PAGE 4
RECYCLED AND STEEL POST SURFACE MOUNT INSTALLATION PROCEDURES Step 1: Determine installation location. Verify concrete footing is a minimum of 6" thick. If the concrete pad is at an angle, steel washers are required to act as shims. (Shims not provided) Step 2: Stand the surface mount post upright onto the concrete pad with a 32" offset on center. Mark the center of the holes on the surface mount plates. After you have made your marks, set aside the posts in order to drill for anchor holes.
PAGE 5
RECYCLED POST PORTABLE INSTALLATION PROCEDURES Step 1: With Holsters installed onto the Instrument (see sheet 6 for Holster installation instructions) place the Portable Posts to a 32" offset on center. Step 2: Place the Instrument Assembly onto the Portable Posts. Verify correct placement, levelness, and plumbness of posts. Step 3: Refer to sheet 6 for installation of instrument to posts. Step 4: Install the Portable Posts Brace 6" below the backside of the Holsters.
PAGE 6
HOLSTER AND INSTRUMENT TO POST INSTALLATION PROCEDURES Step 1: Align Holsters to the instrument back with the corresponding arrows and letters. Fasten Holster to back with the provided dual drive screws. Backs are predrilled. Screw heads should be flush with the Holster surface when properly installed. Holster must also be flush along the back. An extended square drive or Phillips will be needed. Drive screws in slowly to prevent stripping.