Installation Guide

ManualsBrandsUnbranded ManualsGarden CenterSea Flow 8400-GPH High Performance Pond Pump

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

This pool pump must be installed by a licensed or certified electrician or a qualified pool installer in

accordance with the 2008 National Electrical Code (“NEC”) to current and/or all applicable local codes and

ordinances. The specific section of NEC covering your pump may vary depending on your location. Some

states, and/or municipalities may not have adopted the current NEC code. In this case your state or local

code may only be applicable and/or an earlier edition of the NEC may apply. Please check your local and

state codes and regulations before commencing any installation of this pump. Improper installation could

create, among other things, an electrical hazard which may result in death or serious injury to pool users,

installers, or others due to electrical shock, and/or property damage. Always disconnect power to the pool

pump at the circuit breaker before servicing the pump. Failure to do so could result in death or serious injury

to pool users, installers or others (due to electrical shock) and/or property damage.

SEA FLOW

Pump Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Before installing this product, read and follow all warning notices and instructions accompanying this pump. Failure to

follow safety warnings and instructions can result in severe injury, death, or property damage.

WARNING

Attention Installer.

This manual contains important information about the installation, operation and safe use of this product.

This information should be given to the owner/operator of this equipment.

Important Notice

Table of Contents

IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS............................................................................ I-II

SECTION I. GENERAL INFORMATION .............................................................................................................. 1

SECTION II. MAINTENANCE .............................................................................................................................. 2

SECTION III. SERVICE ........................................................................................................................................ 3

SECTION IV. RESTART INSTRUCTIONS ............................................................................................................. 6

SECTION V. TROUBLESHOOTING ..................................................................................................................... 6

SECTION VI. TECHNICAL DATA .......................................................................................................................... 7

A. REPLACEMENT PARTS ............................................................................................................................ 7

B. PUMP CURVES .......................................................................................................................................... 8

P/N 350522 Rev. E 7/12

Summary of content (12 pages)

PAGE 1
SEA FLOW® Pump Owner's Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS ............................................................................ I-II SECTION I. GENERAL INFORMATION .............................................................................................................. 1 SECTION II. MAINTENANCE .............................................................................
PAGE 2
IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS General Warnings • Never open the inside of the drive motor enclosure. There is a capacitor bank that holds a 230 VAC charge even when there is no power to the unit. • The pump is not submersible. • The pump is capable of high flow rates; use caution when installing and programming to limit pumps performance potential with old or questionable equipment. • Code requirements for the electrical connection differ from state to state.
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS For Installation of Electrical Controls at Equipment Pad (ON/OFF Switches, Timers and Automation Load Center) Install all electrical controls at equipment pad, such as on/off switches, timers, and control systems, etc. to allow the operation (startup, shut-down, or servicing) of any pump or filter so the user does not place any portion of his/her body over or near the pump strainer lid, filter lid or valve closures.
PAGE 4
WARNING To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. CAUTION This pump is for use with permanently installed pools and may also be used with hot tubs and spas if so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
PAGE 5
NOTE When pump is mounted permanently within 5 ft. of the inside walls of a swimming pool, you must use a No. 8 AWG or larger conductor to connect to bonding conductor lug. Typical Ground Screw Terminal 7. Bond the motor to the pool structure in accordance with the National Typical Wiring Electrical Code. Use a solid No. 8 AWG or larger copper conductor. Terminals Run a wire from the external bonding to the pool bonding structure, see Figure 1. NPT 1/2” for Cord Strain Relief 8.
PAGE 6
4. 5. 6. 7. Put the debris from the basket into the trash and rinse out the basket. If the basket is cracked, it should be replaced. Replace the basket and fill the pump pot and volute up to the inlet port with water. Clean the cover, cover O-ring, and sealing surface of the pump pot. Grease the O-ring with silicone. Reinstall the lid by placing the clamp and the lid on the pot; see Figure 2. a. Make sure the lid O-ring is properly placed.
PAGE 7
d. If a motor has become wet - let it dry before operating. Do not allow the pump to operate if it has been flooded. e. If a motor has been damaged by water it voids the motor warranty. NOTE DO NOT wrap motor with plastic or other air tight materials. The motor may be covered during a storm, for winter storage, etc., but never when operating, or expecting operation. NOTE When replacing the motor, be certain that the motor support is correctly positioned to support the size of motor being installed.
PAGE 8
f. Hold the impeller securely in place and remove the impeller lock screw by using a #2 Phillips screwdriver. The screw is a left-handed thread and loosens in a clockwise direction. g. Remove the shaft cap located at the back of the motor and hold the shaft secure with a ½ inch open-end wrench. h. To unscrew the impeller from the shaft, twist the impeller counter-clockwise. i. Remove the four bolts from the seal plate to the motor, using a 9/16 inch wrench. j.
PAGE 9
CAUTION The polished and lapped faces of the seal could be damaged if not handled with care. CAUTION In mild climate area, when temporary freezing conditions may occur, run your filtering equipment all night to prevent freezing. SECTION IV. RESTART INSTRUCTIONS A. If pump is installed below the water level of the pool, close return and suction lines prior to opening hair and lint pot on pump. Make sure to reopen valves before to operating. CAUTION DO NOT run the pump dry.
PAGE 10
SECTION VI. TECHNICAL DATA A. Replacement parts. Item No. 1 357199 Clamp, Cam & Ramp, almond 1 357150 Clamp, Cam & Ramp, black 27 071313S 2 Cover, clear, WFE pump 3/4 HP, 60 Hz, WFE-2, 3 & 24, 1 spd., almond, 9 lbs.  357151 27 071314S 2 Cover, chemical resistant Cam & Ramp 1 HP, 60 Hz, WFE-4 & 26, 1 spd., almond, 33 lbs.  357156 27 071315S 3 O-ring, WFE cover 1-1/2 HP, 60 Hz, WFE-6 & 28, 1 spd., almond, 39 lbs.
PAGE 11
26 27 28 B. Pump Curves.
PAGE 12
Warranty Policy • Warranty period starts from date of purchase and must be validated with copy of original purchase receipt. • Warranty requests by phone will not be honored. • Warranty items returned without copy of original purchase receipt will not be honored. • Products purchased from EBay, Craig’s List, etc. cannot be honored for warranty unless returned by original purchaser with proof of purchase.