Specification

ManualsBrandsUnbranded ManualsBathOrigins Single-Handle 1-Spray Shower Faucet with Stops in Chrome (Valve Included)

Origins

™

Model Numbers

Shower System

Speciﬁcation Submittal

S-9601-P

Shower system powered by the Temptrol

Pressure

Balancing valve. Features adjustable stop screw to

limit handle turn, integrated volume control, 1 mode

showerhead with easy to clean rubber nozzles and

standard 2.5 gpm (9.5 L/min) ow restrictor. Components

made from metal and nonmetallic materials plated in

standard polished chrome nish.

Speciﬁcation

Location:

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

Modiﬁcations

Note: Append appropriate -sufx to model number.



S-9601-P

Origins Shower System



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-231 Super showerhead in place of Clear-Flo



-295 Institutional showerhead in place of

Clear-Flo



-X Integral service stops



-CHKS Integral check stops



-IPS

1/2” female IPS connections



-REV Reverse coring for back to back

installations



-B Chrome brass escutcheon



-D Chrome brass dome cover



-VP Vandal proof escutcheon screws



-OP 13” oval plate



-L/HD Less showerhead



-TRM Trim only, valve not included

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

2.0 gpm (7.6 L/min)

Certied by

CSA Group

Reset Form

Summary of content (4 pages)

PAGE 1
Location: Origins™ S-9601-P Shower System Specification Submittal Model Numbers Specification  S-9601-P Shower system powered by the Temptrol® Pressure Balancing valve. Features adjustable stop screw to limit handle turn, integrated volume control, 1 mode showerhead with easy to clean rubber nozzles and standard 2.5 gpm (9.5 L/min) flow restrictor. Components made from metal and nonmetallic materials plated in standard polished chrome finish. Origins Shower System Modifications     -1.5 1.
PAGE 2
Dimensions A Measurements H A B C D I E F G H I J K B C 6 3/8”, 162 mm 3 1/2”, 89 mm 2 7/8”, 73 mm Shower Valve Hole Size Min. Ø 3”, 76 mm Max. Ø 4”, 102 mm Ref. 77”, 1956 mm Rough-in 2 3/8” ± 1/2”, 60 mm ± 13 mm Ref. 42”, 1067 mm Ø 2 1/2”, 64 mm Ø 2 3/4”, 70 mm 2 1/8”, 54 mm Ø 5 3/4”, 146 mm J E D F K G FLOOR Notes: 1) All dimensions measured from nominal rough-in (see F as reference). 2) Dimensions subject to change without notice. Symmons Industries, Inc.
PAGE 3
Emplacement: Origins™ S-9601-P Système de douche Présentation des spécifications Numéro de modèle Spécification  S-9601-P Le système de douche comprend la vanne à pression autorégularisée Temptrol®. Figurer la vis d’arrêt réglable pour limiter le tournage de la poignée, contrôle du volume integer et 1 pomme de douche avec facile à nettoyer les buses en caoutchouc et réducteur de débit régulier de 2,5 gpm (9,5 L/min).
PAGE 4
Dimensions A Mesures H A B C D I E F G H I J K B C 6 3/8 po, 162 mm 3 1/2 po, 89 mm 2 7/8 po, 73 mm Taille du trou Min. Ø 3 po, 76 mm Max. Ø 4 po, 102 mm Réf. 77 po, 1956 mm Robinetterie brute 2 3/8 po ± 1/2 po, 60 mm ± 13 mm Réf. 42 po, 1067 mm Ø 2 1/2 po, 64 mm Ø 2 3/4 po, 70 mm 2 1/8 po, 54 mm Ø 5 3/4 po, 146 mm J E D F K G FLOOR Remarques: 1) Toutes les dimensions sont mesurées à partir de la robinetterie brute nominale (voir F en référence).