SLIM EASY ASSEMBLY TREADMILL SF-T7946 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
EXPLODED DIAGRAM ASSEMBLY CONTENTS When you open the carton, you will find the below parts inside.
PARTS LIST No. Description Spec. Qty. No. Description Spec. Qty.
No Description Spec. Qty. No. Description Spec. Qty 77 . Spring Washer Φ5 2 89 Inclined Tube Plug 78 Screw ST4.2*25 6 90 Lock Washer 79 Screw ST4.2*12 7 91 Control Board 1 80 Screw ST4.2*12 8 92 Fixed Base Plate 2 81 Lock Washer Φ5 2 93 Spring Washer Φ8 2 82 Screw ST4.2*19 18 94 Flat Washer Φ8 2 83 Screw ST4.2*28 4 95 Silicone oil 84 Screw ST4.2*13 22 96 Strenthen Tube Cushion Φ20*8.5*17 2 85 Screw ST2.9*9.
ASSEMBLY INSTRUCTIONS We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 1: Open the carton and remove all contents. Place the Main Frame (No. 1) on level ground and ensure that you have a clean, adequate workspace. STEP 2: Hold up the computer frame. Insert the Rotary Knob (No. 63) to the Right Upright Tube (No. 4) and then screw tightly.
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669). STEP 3: Spin up the Left & Right Handlebars (No. 7 & No. 8) to the horizontal status as the left picture. STEP 4: Insert the Tablet Bracket Front Cover (No. 57) into the computer as the left picture. Put the Safety Key (No. 13) onto the computer.
LUBRICATING THE TREADMILL IMPORTANT NOTE: You will need to lubricate your treadmill before the first use! RUNNING BELTS & TREADMILL LUBRICANT: Lubricating the Running Belt (No. 26) and Running Board (No. 15) is essential as the friction affects the life span and operations of the treadmill. Inspect the Running Belt (No. 26) regularly. If you find any wear on the Running Board (No. 15), please contact us at support@sunnyhealthfitness.com.
MAINTENANCE GUIDE General cleaning will help to prolong the life and improve the performance of your treadmill. Keep the unit clean and maintained by dusting the components on a regular basis. Cleaning the two exposed sides of the Running Belt (No. 26) will prevent dust from accumulating underneath. Keep your running shoes clean so that dirt from the shoes does not wear the Running Belt (No. 26) and Running Board (No. 15). Clean the surface of the Running Belt (No. 26) using a clean damp cloth.
FOLDING INSTRUCTIONS FOLDING: 1. Spin up the Left & Right Handlebars (No. 7 & No. 8) as shown in picture A-A. 2. Unscrew the 2 Rotary Knobs (No. 63) about 10 times until the Rotary Knobs (No. 63) are taken out, then put down the upright tubes as the picture A-C. Screw back the 2 Rotary Knobs (No. 63). 3. Hold the end of the treadmill with both hands and slowly lift the end of the treadmill until it reaches the position as shown in picture A-D.
HOW TO MOVE THE TREADMILL Before attempting to move the treadmill, make sure that it has been properly folded, and the power cord is unplugged. To tilt, start by placing one hand at position “P” to support the top end of the treadmill. Next, place one foot at position “K” to hold the bottom end of the treadmill steady. With your foot at “K”, slowly tilt the top of the treadmill down. Once the Main Frame “P” reaches a low enough point, the wheels of the treadmill will touch the ground.
IMPORTANT ELECTRICAL INFORMATION IMPORTANT NOTE: This treadmill requires a power source of 110 Volts in order to properly operate. For your safety as well as the safety of others, please verify that the power source is correct before powering the equipment. Any power supply source above or below this level could cause significant damage to the equipment and/or user. GROUNDING METHODS: This product must be grounded.
THE DISPLAY CONSOLE LCD WINDOW DISPLAY SPEED: Displays the speed. TIME: Displays the elapsed running time. DISTANCE: Displays the total distance traveled. CALORIES: Displays the total calories burned. BUTTON FUNCTION BUTTON: Press this button to start the treadmill. The treadmill will run at the lowest speed or at the speed of the default program after a 3 second countdown. BUTTON: Press this button to stop the treadmill. The treadmill will slow down until it stops.
MAIN FUNCTION Open the power switch. The window will light up and the treadmill will enter into ready state. START-UP QUICKLY (MANUAL): Attach Safety Key (No. 13) onto the computer, press button. The treadmill will run at the lowest speed in 3 seconds. Press SPEED-/+ buttons to adjust the speed. Press the or remove the Safety Key (No. 13) directly to stop the treadmill.
RUNNING DATA DISPLAY AND SETTING RANGE Show range Mode Program default default Setting range Speed 0.5-7.5MPH -------- -------- -------- Time 0:00—99:59 30:00 30:00 5:00---99:00 Distance 0.00Mile—99.9Mile 1.0 Mile -------- 0.5 Mile —99.9 Mile Calories 0Kcl—990Kcl 50Kcl -------- 10Kcl—990Kcl 8.
EXERCISE INSTRUCTIONS GETTING STARTED Before starting any exercise programs, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the treadmill properly. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
TROUBLESHOOTING CODE PROBLEM POSSIBLE SOLUTION E01 The wire from computer to bottom control board did not connected well E02 Burst Clash Protection E03 No sensor signal E05 Overload Protection 1. Check if the connection wire between computer and control board was well connected. 2. Make sure the IC on the control board was well inserted. If not, re-insert. 3. Abnormal power supply in control board. Please change the control board. 1. Bad contact with the motor’s open circuit.
17