Replacement Part List

ManualsBrandsUnbranded ManualsMiscellaneous PartsTuff Top White Sunshade

1132 W. 1st Street

McPherson, Kansas 67460

1-800-677-0898 1-620-241-3513

Fax 1-620-241-3532

www.femcomfg.com

286333600 3/2/09 Rev N/A

Installation Instructions

FOR

Model SCR-44

Model XLR-52

44” x 44”

48” x 52”

ATTENTION

IF ANY PARTS ARE MISSING OR DAMAGED

DO NOT CALL THE STORE

MADE IN U.S.A.

Page 1 of 6

c:\projects\tuff top 44 & 54\ instructions

Summary of content (6 pages)

PAGE 1
Installation Instructions FOR & Model SCR-44 44” x 44” Model XLR-52 48” x 52” ATTENTION IF ANY PARTS ARE MISSING OR DAMAGED DO NOT CALL THE STORE c:\projects\tuff top 44 & 54\ instructions MADE IN U.S.A. 286333600 3/2/09 Rev N/A Page 1 of 6 1132 W. 1st Street McPherson, Kansas 67460 1-800-677-0898 1-620-241-3513 Fax 1-620-241-3532 www.femcomfg.
PAGE 2
Page 2 of 6
PAGE 3
SCR - 44 ITEM # QTY PART NUMBER PART DESCRIPTION 1 1 1983 CLAMP 2 2 1986 BOW 3 2 1987 EDGE CHANNEL 4 2 1989 LOCK 5 2 202078783 BOLT CRG 3/8 - 16 X 1.50 GR 2 6 4 202659883 BOLT HHCS 3/8 - 16 X 1.00 GR 5 7 2 202720283 WASHER FLAT 184 ANSI A 8 4 230321701 KNOB 9 4 230322001 BUMPER 9/16 10 1 286332000 DECAL WARNING (LOGO) 11 1 286334600 DECAL WARNING (ENGLISH) 12 1 286334700 DECAL WARNING (SPANISH) 13 8 292007083 BOLT HH FLG 1/4 - 20 X .
PAGE 4
IMPORTANT Carefully study exploded view and steps before assembly. leave all hardware loose until instructed to tighten. When assembling, a flat surface will be helpful. STEP 1 1. Starting from the edge of one top panel, slide divider strip on to panel. 2. Center divider strip on panel. Panel Divider Strip 2162_026.JPG 3. Slide other top panel into divider strip. STEP 2 2. On model XLR-52 attach four (4) bow extenders to panel and bow ends using four (4) 1/4 x 1 bolts and lock nuts.
PAGE 5
STEP 4 2162_012.JPG 1. Install rubber bumpers to front and back of left and right struts. STEP 5 1. Remove nuts from bows and attach left and right struts with wide flange facing out. 2126_009.JPG 2126_054.JPG 2. Tighten all bolts. STEP 6 1. For straight up and rear leaning roll bars insert two (2) 3/8 x 1 bolts in holes (A) with head of bolt against weld nut. B A 3. Repeat procedure for other strut and tighten bolts. B A 2126_016.JPG 2. For forward leaning roll bars use holes (B) STEP 7 1.
PAGE 6
STEP 8 1. Lay roll bar bracket on top of roll bar with adjustment teeth towards rear. 2126_031.JPG 2. Attach L-Clamp to roll bar bracket using two (2) 3/8 x 2 bolts and lock nuts on rear top and two (2) 3/8 x 1 1/4 bolts and lock nuts on front bottom. 3. Center bracket assembly on roll bar and tighten bolts. STEP 9 1. Mount assembled TuffTop to roll bar bracket by sliding front bolts into slots (A). A B 3. Slide lock forward over front bolts. 4. Attach four (4) clamp knobs to bolts and tighten.