Instructions / Assembly

1 2 3 4 5 6
7 8 9 10
Owner Manual
Storage Bags
Remote Control
Hand Set
Foot Pedal
Adaptor
Power Cord
SETTING UP YOUR GROW & STOW
™
TREE
Please review these instructions carefully to help you set up your tree.
1. REMOVE ALL PARTS FROM THE BOX
• Tree base in storage bag.
• Tree top in storage bag.
• Parts bag containing remote control, foot pedal, power cord and adaptor,
owners manual, and bulbs.
2. WHEEL TREE BASE TO SET LOCATION
• TIP – Place your tree on a level surface and in a clear
area free of obstructions and near a wall outlet.
1. PLACE SAFETY LOCK SWITCH TO UNLOCK POSITION
2. PRESS THE TREE LOGO BUTTON TO START GROW FUNCTION
• Press this button at any time to control height and toggle
between Grow, Pause, or Stow function.
3. PRESS THE LIGHT BUTTON TO TURN ON/OFF YOUR LIGHTS
AND TO CONTROL LIGHT STRING EFFECTS *
• *Only applicable to tree models with color changing LED lights.
4. IMPORTANT: PLACE SAFTETY LOCK SWITCH TO LOCK POSITION
• To prevent accidental stowing of your tree when fully decorated.
• When in lock position, both the foot pedal and remote control will not
be able to Grow or Stow the tree.
4. REMOVE TREE TOP AND PLACE IN TREE TOP BAG
5. CLOSE PROTECTIVE CAP OVER TREE BASE POLE
6. PULL STORAGE BAG OVER TREE BASE
SHAPING YOUR GROW & STOW
™
TREE
Your Grow & Stow™ Tree is built and designed with Simple Shape® Memory
Wire tips that are already pre-shaped at the factory. However, the rst time you
assemble your tree, it will require minimal shaping due to compression during
packaging. In future seasons, the tree will retain much of the shaping from the
previous season.
STORING YOUR GROW & STOW
™
TREE
1. PLACE SAFETY LOCK SWITCH ON UNLOCK POSITION
2. USE EITHER REMOTE CONTROL OR FOOT PEDAL TO
ACTIVATE THE STOW FUNCTION
• Please make sure to remove all ornaments and
decorations prior to using stow function.
3. UNPLUG THE TREE AND PLACE ALL ACCESSORIES
INTO PARTS BAG
1.
INSERT TWO AAA BATTERIES (NOT INCLUDED)
INTO BATTERY COMPARTMENT
• TIP – Make sure the safety lock switch located on the foot pedal
is in the unlocked position.
2. PRESS THE UP BOTTON TO START GROW FUNCTION
• Press again to stop Grow function and pause at desired tree height.
3. PRESS THE DOWN BOTTON TO START STOW FUNCTION
4. PRESS THE LIGHT BUTTON TO TURN ON/OFF YOUR LIGHTS
AND TO CONTROL LIGHT STRING EFFECTS *
• *Only applicable to tree models with color changing LED lights.
ASSEMBLY AND CARE INSTRUCTIONS
Congratulations on purchasing your new Grow & Stow™ Tree from Polygroup®
GROW & STOW
™
AT A GLANCE
6. ASSEMBLE TREE BY INSERTING THE TREE TOP INTO TREE BASE
• The tree is built with Quick Set® powered pole technology that automatically
lights up the light strings when poles are connected.
• TIP – Make sure tree top is securely inserted into tree base.
You may have to give it a slight turn.
7. CINCH AND TIGHTEN DRAW STRINGS AND
BUCKLE STRAPS
8. UNLOCK WHEELS BEFORE STORING
9. STORE IN COOL, DRY AREA WAY FROM SUNLIGHT
• Exposing your tree to excessive heat or humidity may
damage your tree.
TROUBLESHOOTING
THE TREE LIGHTS DO NOT ILLUMINATE
• Ensure that the power cord is plugged into a wall outlet. If the tree
is plugged into a switch controlled wall outlet, make sure the switch
is turned on.
• Check the remote for batteries and then try switching the remote
o and on.
• Press the light button on the foot pedal.
• If the tree top does not light up, check that the Quick Set® tree top is
securely set into the tree base. You may have to slightly turn or
push down.
• If a section does not illuminate, unplug the power cord and check
that section for loose or missing bulbs. Replace any missing or
broken bulbs (replacement bulbs are included).
Remote Light
Functions Button
Grow
(Up and Pause)
Button
Stow
(Down and Pause)
Button
Remote Battery
Compartment and Lid
Remote LED
Indicator
Light Functions
Push Button
Grow / Pause/
Stow Push Button
Safety Lock
Switch
FOOT PEDAL OPERATION
1 2
OPERATING YOUR GROW & STOW
™
TREE
Your Grow & Stow™ Tree can be operated using either the included foot pedal
or remote control.
THE GROW AND STOW FUNCTIONS DO NOT WORK
• Check to make sure all wires are connected properly following setup instructions.
• Check lock switch on the foot pedal. Switch it to "UNLOCK" position.
THE TREE DOES NOT LOOK STRAIGHT
• Check to make sure the oor is level and that all four wheels are on
the same surface.
PRODUCT SPECIFICATIONS
7. CONNECT WIRES INTO FOOT PEDAL AND POWER ADAPTOR
• Follow corresponding pin connectors to connect tree base to foot pedal.
• Connect to power adaptor and plug into wall socket.
REMOTE CONTROL OPERATION
GROW & STOW
™
INCLUDED ACCESSORIES
Switching Power Supply
(adaptor):
Input AC110-240V, 50/60Hz,
Output DC 29V/2A
7.5ft Tree Grow Range
(Vertical Stroke):
Minimum: 6ft
Maximum: 7.5ft
Stroke: 1.5ft
9ft Tree Grow Range
(Vertical Stroke):
Minimum: 7ft
Maximum: 9ft
Stroke: 2ft
Tree Life Cycle: 3000 Cycles Max.
Remote Controller Range: 33 ft (10m)
Remote Controller Power: DC 3V
Operational Temperature: 0
o
C to 40
o
C, 85% Humidity , indoor use only
Storage Temperature: -5
o
C to 60
o
C, 85% Humidity (and below)
TREE TOP TREE BASE
5. IMPORTANT: PLACE SAFTETY LOCK SWITCH TO LOCK POSITION
• To prevent accidental stowing of your tree when fully decorated.
• When in lock position, both the foot pedal and remote control will not
be able to Grow or Stow the tree.
3. REMOVE TREE PARTS FROM STORAGE BAG
4. LOCK WHEELS ON TREE STAND
5. OPEN PROTECTIVE CAP AT POLE CONNECTION
For immediate help with assembly, product information,
or to order replacement parts, call: 1-888-919-0070,
email: [e-mail] (English, Spanish, French),
(U.S. and Canada only), 10:00 am - 6:00 pm, Monday-Friday,
Eastern Time, or go to www.polygroupstore.com.
SIZE: 787.5 mm x 210 mm
尺寸: 787.5 mm x 210 mm
SIZE: 787.5 mm x 210 mm
材质：300G双粉+双面印刷+过哑胶
颜色：
4 PINS
2 PINS
2 PINS