Use and Care Manual

ManualsBrandsUnbranded ManualsDeck Board SamplesTranscend 1 in. x 5.5 in. x 1 ft. Tree House Composite Decking Board Sample

All exterior building materials require cleaning. Generally, soap and water is all that is required

to clean Trex Transcend, Enhance and Select products. For further information, see below.

TREX TRANSCEND

, TREX ENHANCE

AND

TREX SELECT

CARE AND CLEANING GUIDE

PROBLEM SOLUTION

Dirt and Debris

The affected area should be sprayed off with a hose to remove surface debris. Use warm soapy water and

a soft bristle brush to remove dirt and debris from the embossing pattern.

Hard Water Staining

Hard water is water with a high amount of mineral deposits like lime, silica and calcium. When the water

dries, deposits are left behind, leaving unsightly spots on surfaces. This is not a defect of Trex products

but an issue with the water itself. Generally these deposits can be cleaned with white vinegar on decking

surfaces or use of Magic Eraser

on railing surfaces. Rinsing is required so care should be taken to not

use hard water for this purpose, and if it must be used, dry with a cloth or use a blower to dry surfaces.

Chalk Lines

Most colored chalks are permanent and may discolor the surface. Use only Irwin Strait-Line

* Dust-Off

Marking Chalk (purple), available at Irwin.com

Tannins Due to Debris

Remove all debris from the deck using a hose or broom. Once the deck surface is dry, apply a deck

“brightener”** to the deck as directed by the manufacturer. Deck Brighteners contain oxalic acid, which

will also remove tannins.

Ice and Snow

A plastic shovel may be used to remove snow from the deck. Use calcium chloride or rock salt to melt the

snow and ice from the deck surface.

Oil, Grease and Food

All food spills should be removed as soon as possible. The surface must be cleaned within seven days

to maintain the stain warranty. To remove, spray off with a hose and use warm, soapy water and a soft

bristle brush to remove spills from the embossing pattern.

Mold and Mildew

If debris such as pollen and dirt is allowed to remain on the deck surface, mold can feed on the bioﬁlm.

Using a hose and warm, soapy water with a soft bristle brush is recommended to remove the food source

and mold.

Using a Pressure Washer (Concrete,

Stucco or Ground-in Construction Dirt)

A pressure washer with no greater than 3100 psi*** that has a fan attachment/adjustment and soap

dispenser may be used to remove dirt, concrete dust, or other types of construction dirt. Spray deck

with soap, then follow with gently scrubbing each deck board with a soft bristle brush. Spray/rinse each

individual deck board using a fan tip no closer than 8-in from the decking surface. RINSE THOROUGHLY.

If dirty water from cleaning is left to dry, this will cause a ﬁlm to remain on the decking surface.

Maintaining Transcend and Select Railing

NEVER use acetone or other solvents on Trex Transcend or Select railing to maintain the beauty of the

surface. For color transfer issues (from attachment of baluster spacer), use Mr. Clean

Magic Eraser

Original or Magic Eraser

Extra Power to help remove this.**** For small surface scratches, marks or

scuffs, use Dupli-Color Scratch Seal™ Clear Sealer Pen.*****

Job Site Storage

Store decking on a ﬂat level surface, and always use proper supports (dunnage). Do not store

directly on the ground. When stacking decking bundles, supports (dunnage) should start approximately

8-in (0.20 m) from each end and be spaced approximately 2-ft (0.61 m) on center. In addition, supports

(dunnage) should line up vertically/perpendicular to the decking product. Adjust support blocks

(dunnage) accordingly if bundles are loose. For Select decking, 1x12 and 1x8 products, the maximum

stack height is 12 bundles. For all other decking products maximum stack height is 14 bundles

(IMPORTANT TO NOTE THAT PROPER DUNNAGE SPACING MUST BE IN PLACE FOR THESE HEIGHTS.)

When stacking multiple bundles, ensure that dunnage lines up vertically down through each stack. Always

cover decking products on site until ready to be installed.

*Strait-Line

is a registered trademark of Irwin Industrial Tool Company.

**Use of products containing bleach or acid will lighten the surface of Trex. Use in an inconspicuous area to determine whether you like the effect. Neither product will affect the structural integrity of Trex.

***Use of a pressure washer greater than 3100 psi could damage the boards and void the warranty.

****Mr. Clean

and Magic Eraser

are registered trademarks of The Procter and Gamble Company.

*****Scratch Seal™ Clear Sealer Pen is a registered trademark of Dupli-Color

Products Company.